Difficulty

Moderate

Steps

8

Time Required

Suggest a time??

Sections

1

  • To open
  • 8 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSaeco Odea

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              To open
  • Warning: Unplug the device from power before you start!
  • Remove all attachments such as the water tank, pomace container, brew group and drip tray.
  • Remove all the coffee beans from the machine.

Warning: Unplug the device from power before you start!

Remove all attachments such as the water tank, pomace container, brew group and drip tray.

Remove all the coffee beans from the machine.

1024

Step 2

  • Pull the steam valve button up.
  • Pull the bezel ring around the knob

Pull the steam valve button up.

Pull the bezel ring around the knob

Step 3

  • Remove the cover from the coffee spout. Lift them from bottom to top, using only plastic tools to pry.

Remove the cover from the coffee spout. Lift them from bottom to top, using only plastic tools to pry.

Step 4

  • Unscrew the two Torx T10 screws on the coffee spout.
  • Pull off the coffee spout.

Unscrew the two Torx T10 screws on the coffee spout.

Pull off the coffee spout.

Step 5

  • Using a Torx T10 screwdriver remove the single screw from the bean container.
  • Lift the bean container up and remove it.

Using a Torx T10 screwdriver remove the single screw from the bean container.

Lift the bean container up and remove it.

Step 6

  • The large silver-colored molded part above the top and front is now only fastened with catches, which can, however, be quite stuck. Only use plastic tools to pry loose.
  • Slide the cup holder all the way down.
  • Start to pry off the molded part at the back seam, the catches gradually loosen with a loud crack.
  • It’s a bit tricky to slide the cover over the steam valve knob, you need some strength to do it.
  • Under the bean container, you’ll find the white magnetic contact (reed contact) for the bean container lid. Lift it up and drop it through the opening in the molding.
  • Lift up the cover.

The large silver-colored molded part above the top and front is now only fastened with catches, which can, however, be quite stuck. Only use plastic tools to pry loose.

Slide the cup holder all the way down.

Start to pry off the molded part at the back seam, the catches gradually loosen with a loud crack.

It’s a bit tricky to slide the cover over the steam valve knob, you need some strength to do it.

Under the bean container, you’ll find the white magnetic contact (reed contact) for the bean container lid. Lift it up and drop it through the opening in the molding.

Lift up the cover.

Step 7

  • Now only the two side parts are left. The left side part contains the steam pipe. Most of the time you can leave the pressure hose of the steam pipe connected, then the side part cannot be completely removed, but that doesn’t bother you very much.
  • The two side parts are attached with a few Torx T10 screws, unscrew them:
  • A screw at the top back
  • A screw at the top
  • Four screws on the front

Now only the two side parts are left. The left side part contains the steam pipe. Most of the time you can leave the pressure hose of the steam pipe connected, then the side part cannot be completely removed, but that doesn’t bother you very much.

The two side parts are attached with a few Torx T10 screws, unscrew them:

A screw at the top back

A screw at the top

Four screws on the front

Step 8

  • Remove two screws on the side with the water tank.
  • The side parts are jammed. Start to pry apart the two side pieces at the back seam.
  • Pry off the two side parts with a plastic tool. Pay attention to the power connection.

Remove two screws on the side with the water tank.

The side parts are jammed. Start to pry apart the two side pieces at the back seam.

Pry off the two side parts with a plastic tool. Pay attention to the power connection.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      13 other people completed this guide.                                             


        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

Julian Sailer

Fabian Neidhardt

Idrees

VauWeh

and 2 others…

                 +2

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges

Uwe - Apr 8, 2020

Reply

Hat funktioniert.

mar hag - Aug 5, 2020

Reply

Vielen Dank ist super beschrieben und hat funktioniert

michael.gensler - Dec 10, 2020

Reply

Danke. Hat prima funktioniert.

Julian Sailer - Dec 10, 2020

Reply

Perfect immer schön positives Feedback zu bekommen

VauWeh - Dec 10, 2020

Jawoll! Freut mich! :-)