Opening Procedure Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 30 minutes

Sections

Opening Procedure
9 steps

Flags

BackApple Watch - Series 6
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

You’ll need replacement adhesive to reattach the display when reassembling the device.

What you need

Step 1

              Power down the watch

Before starting repairs, take your watch off the charger and power it down.
If your touchscreen is broken and you can’t power off the watch, use this alternate method to power it down.

Before starting repairs, take your watch off the charger and power it down.

If your touchscreen is broken and you can’t power off the watch, use this alternate method to power it down.

1024

Step 2

              Safety Requirements

Because the gap between the screen and watch body is so thin, a sharp blade is needed to separate the two. Read the following warnings carefully before proceeding.
Protect your fingers by keeping them completely clear of the knife. If in doubt, protect your free hand with a heavy glove, such as a leather shop glove or gardening glove.
Be careful not to apply too much pressure, as this might cause the knife to slip and cut you, or damage the watch.
Wear eye protection. The knife or glass may break, sending pieces flying.
Attach or remove the watch band as needed to provide more control as you make repairs.

Because the gap between the screen and watch body is so thin, a sharp blade is needed to separate the two. Read the following warnings carefully before proceeding.

Protect your fingers by keeping them completely clear of the knife. If in doubt, protect your free hand with a heavy glove, such as a leather shop glove or gardening glove.

Be careful not to apply too much pressure, as this might cause the knife to slip and cut you, or damage the watch.

Wear eye protection. The knife or glass may break, sending pieces flying.

Attach or remove the watch band as needed to provide more control as you make repairs.

Step 3

              Soften the display adhesive

Prepare an iOpener (or use a hair dryer or heat gun) and heat the face of the watch to loosen the display adhesive.
Leave the iOpener on the watch for at least two minutes to fully heat the screen and soften the adhesive holding it to the case.
You may need to reheat the iOpener and repeat this procedure several times until the display adhesive softens.

Prepare an iOpener (or use a hair dryer or heat gun) and heat the face of the watch to loosen the display adhesive.

Leave the iOpener on the watch for at least two minutes to fully heat the screen and soften the adhesive holding it to the case.

You may need to reheat the iOpener and repeat this procedure several times until the display adhesive softens.

Step 4

              Display opening

Place the edge of a curved blade into the thin gap between the display and the outer case. Start at the short side of the display, most distant to the digital crown.
Press firmly straight down into the gap.
Once inserted, tilt the blade to pry the display open slightly.

Place the edge of a curved blade into the thin gap between the display and the outer case. Start at the short side of the display, most distant to the digital crown.

Press firmly straight down into the gap.

Once inserted, tilt the blade to pry the display open slightly.

Step 5

Insert an opening pick in the gap your created.
Slide the opening pick along the short edge of the watch to cut the adhesive.

Insert an opening pick in the gap your created.

Slide the opening pick along the short edge of the watch to cut the adhesive.

Step 6

Slide the opening pick around the corner and along the long edge on the opposite side of the watch crown to cut the display adhesive.

Slide the opening pick around the corner and along the long edge on the opposite side of the watch crown to cut the display adhesive.

Step 7

Slide the opening pick around the corner to cut the remaining adhesive on the short edge of the watch next to the watch crown.

Slide the opening pick around the corner to cut the remaining adhesive on the short edge of the watch next to the watch crown.

Step 8

Place the watch on a flat surface and use an opening pick to slice through any remaining adhesive.
Try not to slice near the watch crown to prevent damaging the display cables. If you must slice near the crown, don’t insert the opening pick deeper than 1/16th of an inch (~2 mm).
Slide an opening pick under the opposite display edge of the watch crown.
Twist the opening pick to loosen the display off the watch case.
Don’t try to remove the display. It is still connected to the watch assembly.

Place the watch on a flat surface and use an opening pick to slice through any remaining adhesive.

Try not to slice near the watch crown to prevent damaging the display cables. If you must slice near the crown, don’t insert the opening pick deeper than 1/16th of an inch (~2 mm).

Slide an opening pick under the opposite display edge of the watch crown.

Twist the opening pick to loosen the display off the watch case.

Don’t try to remove the display. It is still connected to the watch assembly.

Step 9

Be careful not to strain the display cables when you fold the display to the side.
Lift the display and carefully pull it towards the watch crown.
Swing the display open to an upward position.

Be careful not to strain the display cables when you fold the display to the side.

Lift the display and carefully pull it towards the watch crown.

Swing the display open to an upward position.

To reassemble your Apple Watch Series 6, follow these instructions in reverse order.

Apply a little bit of high isopropyl alcohol (>90%) to a Q-tip or use a cleaning pad to gently remove the leftover adhesive on the edges of the watch case and the screen before installing new adhesive.

Opening didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 1 other contributor

                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team