Difficulty

Moderate

Steps

7

Time Required

Suggest a time??

Sections

2

  • Opening the Siemens Surpresso Compact
  • 6 steps
  • Opening the Grinder
  • 1 step

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSiemens Surpresso Compact TK52001

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Opening the Siemens Surpresso Compact
  • Unplug your coffee maker!
  • Remove the water container, the brew group and the drip tray with pomace container.
  • Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.
  • Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

Unplug your coffee maker!

Remove the water container, the brew group and the drip tray with pomace container.

Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.

Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

1024

Step 2

  • Remove the two Torx T10 screws on the top.

Remove the two Torx T10 screws on the top.

Step 3

  • Remove seven T10 Torx screws on the back.
  • The two screws at the bottom of the front can remain.

Remove seven T10 Torx screws on the back.

The two screws at the bottom of the front can remain.

Step 4

  • Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.
  • Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.
  • Lift the top off.
  • On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.

Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.

Lift the top off.

On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

Step 5

  • Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.
  • Remove the two tabs from the power switch.
  • Take off the side panel with the brew group.

Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.

Remove the two tabs from the power switch.

Take off the side panel with the brew group.

Step 6

  • Do the same with the panel on the other side.
  • To remove the water tank hose simply pull it of the pump.
  • Remove the side panel.

Do the same with the panel on the other side.

To remove the water tank hose simply pull it of the pump.

Remove the side panel.

Step 7

              Opening the  Grinder
  • The grinder is situated on the top right rearside of the device. The adjuster and the outer ring can just be taken off, but this is only necessary if the grinder has to be completely replaced. Be careful and do not use excessive force.
  • Beyond the white ring with the holes there is a small springloaded ball (3.2 mm diameter). It ensures that the ring clicks into place, hence the click. Be careful, it can fall out and get lost.
  • The following pictures show a grinder of a Jura and there are slight differences. But since the grinder is the same, the repair is basically the same.

The grinder is situated on the top right rearside of the device. The adjuster and the outer ring can just be taken off, but this is only necessary if the grinder has to be completely replaced. Be careful and do not use excessive force.

Beyond the white ring with the holes there is a small springloaded ball (3.2 mm diameter). It ensures that the ring clicks into place, hence the click. Be careful, it can fall out and get lost.

The following pictures show a grinder of a Jura and there are slight differences. But since the grinder is the same, the repair is basically the same.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             


        VauWeh is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges