Difficulty

Moderate

Steps

11

Time Required

                          10 - 15 minutes

Sections

1

  • Opening the Huawei Watch 3
  • 11 steps

Flags

0

  • BackHuawei Watch 3

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove both wrist bands
  • User your fingernail to pull the small metal pin on each wrist band towards the inside. This unlocks the wrist bands from the body of the watch.
  • Remove the wrist bands.

User your fingernail to pull the small metal pin on each wrist band towards the inside. This unlocks the wrist bands from the body of the watch.

Remove the wrist bands.

1024

Step 2

              Remove the four Torx screws
  • Use a Torx T3 screwdriver to remove the four 4 mm-long screws on the back of the Huawei Watch 3.

Use a Torx T3 screwdriver to remove the four 4 mm-long screws on the back of the Huawei Watch 3.

Step 3

              Pry the back cover open
  • Locate the small notch at the top of the back cover.
  • Use a Jimmy to pry open the back cover by twisting it.
  • Using a sharp metal tool might cause cosmetic damage to the watch case. Covering the tool with a nitril glove can minimize the damage.
  • Don’t remove the back cover just yet. It is still connected to the motherboard with a flex cable.

Locate the small notch at the top of the back cover.

Use a Jimmy to pry open the back cover by twisting it.

Using a sharp metal tool might cause cosmetic damage to the watch case. Covering the tool with a nitril glove can minimize the damage.

Don’t remove the back cover just yet. It is still connected to the motherboard with a flex cable.

Step 4

              Loosen the back cover gasket
  • Insert the tip of an opening pick between the back cover and the case.
  • Slide the opening pick around the back cover to loosen the gasket from the back cover.

Insert the tip of an opening pick between the back cover and the case.

Slide the opening pick around the back cover to loosen the gasket from the back cover.

Step 5

              Lift the back cover
  • There is a ribbon cable running from the back cover to the motherboard.
  • Use an opening pick or your fingers to carefully lift the back cover open.
  • Flip the back cover open away from the crown.
  • You can prop up the back cover to minimize the stress on the ribbon cable.

There is a ribbon cable running from the back cover to the motherboard.

Use an opening pick or your fingers to carefully lift the back cover open.

Flip the back cover open away from the crown.

You can prop up the back cover to minimize the stress on the ribbon cable.

Step 6

              Remove the battery bracket screw
  • Use a Phillips screwdriver to remove the 2.9 mm-long screw from the battery bracket.

Use a Phillips screwdriver to remove the 2.9 mm-long screw from the battery bracket.

Step 7

              Remove the battery bracket
  • User a pair of tweezers to lift the top of the battery bracket free from its screw socket.
  • Unhook the opposite side of the bracket and remove it.

User a pair of tweezers to lift the top of the battery bracket free from its screw socket.

Unhook the opposite side of the bracket and remove it.

Step 8

              Unplug the battery connector
  • Use the tip of a spudger to pry up and disconnect the battery connector.
  • The battery connector is the smallest of the three connectors.

Use the tip of a spudger to pry up and disconnect the battery connector.

The battery connector is the smallest of the three connectors.

Step 9

              Remove the sensor bracket screw
  • Use a Phillips screwdriver to remove the 2.9 mm-long screw from the sensor bracket.

Use a Phillips screwdriver to remove the 2.9 mm-long screw from the sensor bracket.

Step 10

              Remove the sensor bracket
  • User a pair of tweezers to move the top of the sensor bracket free from a small latch near the case by rotating in inwards.
  • Unhook the opposite side of the bracket and remove it.

User a pair of tweezers to move the top of the sensor bracket free from a small latch near the case by rotating in inwards.

Step 11

              Unplug the sensor connector
  • Use the tip of a spudger to pry up and disconnect the sensor connector.
  • Remove the back cover.

Use the tip of a spudger to pry up and disconnect the sensor connector.

Remove the back cover.

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our https://www.ifixit.com/Answers/Device/Hu… for help.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Tobias Isakeit

Member since: 03/31/2014

105,397 Reputation

                                      184 Guides authored                  



                       Badges:
                       46







                                                        +43 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored