Difficulty
Difficult
Steps
10
Time Required
30 - 45 minutes
Sections
2
- Induction Charging Coil
- 7 steps
- Battery
- 3 steps
Flags
0
BackOral-B Triumph v2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Induction Charging Coil
- Use the charging station to remove the a small plastic plug from the end of the toothbrush by inserting the charging station into the end insert and twisting counter-clockwise by 90 degrees.
Use the charging station to remove the a small plastic plug from the end of the toothbrush by inserting the charging station into the end insert and twisting counter-clockwise by 90 degrees.
1024
Step 2
- Remove the end cap from the bottom of the toothbrush by prying it off with a spudger.
Remove the end cap from the bottom of the toothbrush by prying it off with a spudger.
Step 3
- Remove the top cap by using a spudger to pry the plastic ring off of the toothbrush frame.
Remove the top cap by using a spudger to pry the plastic ring off of the toothbrush frame.
Step 4
- Use a spudger to loosen the two plastic tabs next to the induction coil that secure the internal assembly to the frame.
- Push on the rotating head in order to pop the assembly out of the black plastic casing.
- You can also use a spudger to leverage the assembly out, but this may break the copper wire connected to the induction coil, so be careful.
Use a spudger to loosen the two plastic tabs next to the induction coil that secure the internal assembly to the frame.
Push on the rotating head in order to pop the assembly out of the black plastic casing.
You can also use a spudger to leverage the assembly out, but this may break the copper wire connected to the induction coil, so be careful.
Step 5
- Unwrap the ends of the wires from the white plastic pegs using a pair of tweezers.
- Each wire end is wrapped around the peg 3-4 times.
Unwrap the ends of the wires from the white plastic pegs using a pair of tweezers.
Each wire end is wrapped around the peg 3-4 times.
Step 6
- Melt the solder at the two pads on either side of the top of the motherboard. This will require a high heat soldering iron. Remove the wire from the solder pads using tweezers once the solder melts.
Melt the solder at the two pads on either side of the top of the motherboard. This will require a high heat soldering iron. Remove the wire from the solder pads using tweezers once the solder melts.
Step 7
- Remove the induction coil by pulling the plastic tabs out of their keepers.
- A spudger can be used to remove the plastic tabs from their keepers if neccessary.
Remove the induction coil by pulling the plastic tabs out of their keepers.
A spudger can be used to remove the plastic tabs from their keepers if neccessary.
Step 8
Battery
- Remove the spring from the housing using a nylon spudger.
Remove the spring from the housing using a nylon spudger.
Step 9
- Use a soldering iron to melt the solder pad at the top of the motherboard, which attaches a battery electrode to the board. Remove the electrode by pulling it through the plastic housing after it has been desoldered from the board.
- Repeat with the two solder pads on either side of the motherboard just above the black diamond-shaped component. The electrode foils can be pulled through the board from the back after the solder is melted.
Use a soldering iron to melt the solder pad at the top of the motherboard, which attaches a battery electrode to the board. Remove the electrode by pulling it through the plastic housing after it has been desoldered from the board.
Repeat with the two solder pads on either side of the motherboard just above the black diamond-shaped component. The electrode foils can be pulled through the board from the back after the solder is melted.
Step 10
- Use a metal spudger to pop the battery out of its casing. The electrodes will remain attached to the battery.
Use a metal spudger to pop the battery out of its casing. The electrodes will remain attached to the battery.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 3 other contributors
Jonathan Bowyer
Member since: 11/06/2017
369 Reputation
3 Guides authored
Badges:
10
+7 more badges
Team
IUPUI, Team S1-G1, Harley Fall 2017
Member of IUPUI, Team S1-G1, Harley Fall 2017
IUPUI-HARLEY-F17S1G1
3 Members
12 Guides authored
Andreas Kappos - Sep 25, 2019
Reply
Wo bekommt man einen neuen AKU
Andreas
VauWeh - Sep 25, 2019
Der sollte es sein. Er muss Lötfahnen haben! Miss die Länge nach, 42 oder 48 mm.
