Oral B Black 7000 Induction Coil Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          15 - 30 minutes

Sections

Induction Charging Coil
7 steps

Flags

BackOral-B Triumph v2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Induction Charging Coil

Use the charging station to remove the a small plastic plug from the end of the toothbrush by inserting the charging station into the end insert and twisting counter-clockwise by 90 degrees.

Use the charging station to remove the a small plastic plug from the end of the toothbrush by inserting the charging station into the end insert and twisting counter-clockwise by 90 degrees.

1024

Step 2

Remove the end cap from the bottom of the toothbrush by prying it off with a spudger.

Remove the end cap from the bottom of the toothbrush by prying it off with a spudger.

Step 3

Remove the top cap by using a spudger to pry the plastic ring off of the toothbrush frame.

Remove the top cap by using a spudger to pry the plastic ring off of the toothbrush frame.

Step 4

Use a spudger to loosen the two plastic tabs next to the induction coil that secure the internal assembly to the frame.
Push on the rotating head in order to pop the assembly out of the black plastic casing.
You can also use a spudger to leverage the assembly out, but this may break the copper wire connected to the induction coil, so be careful.

Use a spudger to loosen the two plastic tabs next to the induction coil that secure the internal assembly to the frame.

Push on the rotating head in order to pop the assembly out of the black plastic casing.

You can also use a spudger to leverage the assembly out, but this may break the copper wire connected to the induction coil, so be careful.

Step 5

Unwrap the ends of the wires from the white plastic pegs using a pair of tweezers.
Each wire end is wrapped around the peg 3-4 times.

Unwrap the ends of the wires from the white plastic pegs using a pair of tweezers.

Each wire end is wrapped around the peg 3-4 times.

Step 6

Melt the solder at the two pads on either side of the top of the motherboard. This will require a high heat soldering iron. Remove the wire from the solder pads using tweezers once the solder melts.

Melt the solder at the two pads on either side of the top of the motherboard. This will require a high heat soldering iron. Remove the wire from the solder pads using tweezers once the solder melts.

Step 7

Remove the induction coil by pulling the plastic tabs out of their keepers.
A spudger can be used to remove the plastic tabs from their keepers if neccessary.

Remove the induction coil by pulling the plastic tabs out of their keepers.

A spudger can be used to remove the plastic tabs from their keepers if neccessary.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors

                    Rachel Surridge

Member since: 11/06/2017

292 Reputation

                                      1 Guide authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       IUPUI, Team S1-G1, Harley Fall 2017                        

                                                  Member of IUPUI, Team S1-G1, Harley Fall 2017 



                    IUPUI-HARLEY-F17S1G1                     


                                            3 Members                     


                                            12 Guides authored

Geoffrey Sacré - May 26, 2021

bonjour, ou puis je trouver une nouvelle bobine d’induction ou puis je remplacer simplement le fil de cuivre

juste une précision pour sortir l’intérieur de la brosse du manche il faut appuyez sur les deux pattes plastique en bas près de la boucle d’induction

on voit une des pattes a l’étape 5

Introduction#

What you need#

Team#

Introduction

What you need

Team