Orbic Wonder Charging Port Circuit Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 - 45 minutes

Sections

Battery
5 steps
Speaker
2 steps
Charging Port Circuit Board
3 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackOrbic Wonder
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Battery

Remove two 2mm TR9 Torx screws from the bottoms of the device.

Remove two 2mm TR9 Torx screws from the bottoms of the device.

1024

Step 2

There is a border between the black phone backing and the silver screen.
Place the Jimmy in this border, and cautiously torque it back and forth to part the two halves.
When the halves are parted correctly, the gap should look like this.
Be careful to avoid damaging any connecting circuitry between the two halves.

There is a border between the black phone backing and the silver screen.

Place the Jimmy in this border, and cautiously torque it back and forth to part the two halves.

When the halves are parted correctly, the gap should look like this.

Be careful to avoid damaging any connecting circuitry between the two halves.

Step 3

Before continuing, tighten the anti-static wrist strap around your wrist and connect the alligator clips to a metal portion of the phone.
On the upper right side, there is a black ribbon cable in the shape of an “L”. Remove the single 1 mm Phillips #000 screw on the left side of the ribbon cable.

Before continuing, tighten the anti-static wrist strap around your wrist and connect the alligator clips to a metal portion of the phone.

On the upper right side, there is a black ribbon cable in the shape of an “L”. Remove the single 1 mm Phillips #000 screw on the left side of the ribbon cable.

Step 4

Use a pair of angled tweezers to carefully remove the metal casing of the ribbon cable.
Use a pair of angled tweezers to detach the black ribbon cable. This is done to unplug the battery.

Use a pair of angled tweezers to carefully remove the metal casing of the ribbon cable.

Use a pair of angled tweezers to detach the black ribbon cable. This is done to unplug the battery.

Step 5

There is a black flap on the bottom of the battery.
Using your fingers, pinch this flap and carefully pull the battery up and out of the phone.

There is a black flap on the bottom of the battery.

Using your fingers, pinch this flap and carefully pull the battery up and out of the phone.

Step 6

              Speaker

Remove the anti-static wrist strap.
Use the Phillips #000 screwdriver to remove the five black 2 mm screws.
Use the Phillips #000 screwdriver to remove the two grey 2 mm screws.

Remove the anti-static wrist strap.

Use the Phillips #000 screwdriver to remove the five black 2 mm screws.

Use the Phillips #000 screwdriver to remove the two grey 2 mm screws.

Step 7

Use a pair of angled tweezers to remove the speaker housing.

Use a pair of angled tweezers to remove the speaker housing.

Step 8

              Charging Port Circuit Board

Detach the metal casing at the bottom of the phone.
Unplug the cable connector.
Use a pair of angled tweezers to unplug the black wire.

Detach the metal casing at the bottom of the phone.

Unplug the cable connector.

Use a pair of angled tweezers to unplug the black wire.

Step 9

Using a pair of angled tweezers, disconnect the connector chip.
With the angled tweezers, gently lift (but do not remove) the green circuit board from the phone.

Using a pair of angled tweezers, disconnect the connector chip.

With the angled tweezers, gently lift (but do not remove) the green circuit board from the phone.

Step 10

Using a pair of angled tweezers, disconnect the attachment to the microphone labeled “JD,” and completely remove the circuit board.

Using a pair of angled tweezers, disconnect the attachment to the microphone labeled “JD,” and completely remove the circuit board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Grant Adler

Member since: 09/17/2019

841 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Embry-Riddle Aeronautical University, Team S20-G1, Branham Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S20-G1, Branham Fall 2019 



                    ERAU-BRANHAM-F19S20G1                     


                                            4 Members                     


                                            10 Guides authored

Better Introduction#

What you need#

Team#

Better Introduction

What you need

Team