Oregon Scientific Rm318Pa Lens Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes

Sections

Lens
11 steps

Flags

BackOregon Scientific RM318PA
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              A/C Adapter

Hold clock so the screen is facing away from you.
Using your thumbs, push up on battery cover to remove.
With your other hand, pull down on the A/C Adapter jack to remove.

Hold clock so the screen is facing away from you.

Using your thumbs, push up on battery cover to remove.

With your other hand, pull down on the A/C Adapter jack to remove.

1024

Step 2

              Batteries

Remove batteries by pushing a battery toward the spring.
Lift battery out at an angle. Repeat with second battery.

Remove batteries by pushing a battery toward the spring.

Lift battery out at an angle. Repeat with second battery.

Step 3

              Projection Arm

Use a Phillips #00 Screwdriver to remove the four (4) screws from the back of the projection arm.
Once screws are removed, lift the back up and off of the projection arm.

Use a Phillips #00 Screwdriver to remove the four (4) screws from the back of the projection arm.

Once screws are removed, lift the back up and off of the projection arm.

Step 4

              Screws Projection Arm

Use a Phillips #00 Screwdriver to remove two (2) screws from back of projection arm.

Use a Phillips #00 Screwdriver to remove two (2) screws from back of projection arm.

Step 5

              Front of the Projection Arm

Use a Plastic Opening Tool to pry open the front of the projection arm casing. Start at the top of the projection arm.
Once top is partially open, use a Spudger to pry at the side of the projection arm.

Use a Plastic Opening Tool to pry open the front of the projection arm casing. Start at the top of the projection arm.

Once top is partially open, use a Spudger to pry at the side of the projection arm.

Step 6

              Projection Beam

Turn the clock on its side. Slide the focus wheel forward with your thumb.
The Projection Beam and Focus Wheel Component should now be free of Projection Arm.
Hold the Component in one hand and lift the Projection Beam up and away from the Focus Wheel.

Turn the clock on its side. Slide the focus wheel forward with your thumb.

The Projection Beam and Focus Wheel Component should now be free of Projection Arm.

Hold the Component in one hand and lift the Projection Beam up and away from the Focus Wheel.

Step 7

              The Lens

The Lens is attached to the Focus Knob and is now accessible for replacement purposes.

The Lens is attached to the Focus Knob and is now accessible for replacement purposes.

Step 8

              Tape

Apply tape to the lens for safe removal and prevention of injury.

Apply tape to the lens for safe removal and prevention of injury.

Step 9

              Focus Knob

Detach the focus knob from the internal casing of the lens by removing the screw from the base of the focus knob grip.
Pry apart the pieces of casing holding the focus knob in place and remove the knob.

Detach the focus knob from the internal casing of the lens by removing the screw from the base of the focus knob grip.

Pry apart the pieces of casing holding the focus knob in place and remove the knob.

Step 10

              Internal Casing

Insert the spudger into the opening above the hinge on the side of the casing.
Press down firmly until the case opens.

Insert the spudger into the opening above the hinge on the side of the casing.

Press down firmly until the case opens.

Step 11

              Lens Removal

Pull apart the casing and gently slide lens from pocket.
Be sure to replace with a concave lens.

Pull apart the casing and gently slide lens from pocket.

Be sure to replace with a concave lens.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Maxine Holden

Member since: 10/27/2014

476 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Eastern Washington University, Team 1-6, Carnegie Fall 2015                        

                                                  Member of Eastern Washington University, Team 1-6, Carnegie Fall 2015 



                    EWU-CARNEGIE-F15S1G6                     


                                            1 Member                     


                                            4 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team