Difficulty

Difficult

Steps

10

Time Required

                          30 minutes

Sections

2

  • Osmo Mobile Handle Disassembly
  • 6 steps
  • Bluetooth Module
  • 4 steps

Flags

0

  • BackDJI Osmo Mobile

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Osmo Mobile Handle Disassembly
  • Remove gimbal from base handle by loosening round plate found at the top of the handle.

Remove gimbal from base handle by loosening round plate found at the top of the handle.

1024

Step 2

  • Use Phillips #00 screwdriver to remove the three screws found on the gimbal stabilizer to detach handle from gimbal.
  • Carefully detach handle from gimbal and disconnect the cable that connects the two.

Use Phillips #00 screwdriver to remove the three screws found on the gimbal stabilizer to detach handle from gimbal.

Carefully detach handle from gimbal and disconnect the cable that connects the two.

Step 3

  • Locate the hex screws found at the top base of the handle, and unscrew using the 1.5mm hex screwdriver.

Locate the hex screws found at the top base of the handle, and unscrew using the 1.5mm hex screwdriver.

Step 4

  • Remove joystick by gently pulling away from handle

Remove joystick by gently pulling away from handle

Step 5

  • Remove the quick release PCBA by locating the connecting wires and release the ribbon cable with tweezers.
  • Use the spudger to pry open and remove the face plate, starting at the back of the handle.

Remove the quick release PCBA by locating the connecting wires and release the ribbon cable with tweezers.

Use the spudger to pry open and remove the face plate, starting at the back of the handle.

Step 6

  • Locate four screws directly on top of handle.
  • Unscrew the silver, bottom two screws, that are closest to the face plate using the 00 screwdriver.
  • Unscrew the black, top two screws, located furthest from the face plate, using the 0 screwdriver.
  • Remove the remaining two screws found on the front of the faceplate.
  • Remove the rest of the face plate shell.

Locate four screws directly on top of handle.

Unscrew the silver, bottom two screws, that are closest to the face plate using the 00 screwdriver.

Unscrew the black, top two screws, located furthest from the face plate, using the 0 screwdriver.

Remove the remaining two screws found on the front of the faceplate.

Remove the rest of the face plate shell.

Step 7

              Bluetooth Module
  • Locate and remove the black screw found at the base of the grey mounting plate.
  • Remove the grey face plate.

Locate and remove the black screw found at the base of the grey mounting plate.

Remove the grey face plate.

Step 8

  • Open the battery hatch and remove it by using the tweezers to press the hinge into the device.
  • Remove the black screw located underneath where the battery hatch was.

Open the battery hatch and remove it by using the tweezers to press the hinge into the device.

Remove the black screw located underneath where the battery hatch was.

Step 9

  • Use the spudger to remove the front handle casing by sliding the spudger into the area between the handle grooves.
  • Slide the spudger around the groove to find the 6 clasps that hold the front part of the handle, and unclasp them.
  • Take off the front handle section to reveal the whole interior of the device.

Use the spudger to remove the front handle casing by sliding the spudger into the area between the handle grooves.

Slide the spudger around the groove to find the 6 clasps that hold the front part of the handle, and unclasp them.

Take off the front handle section to reveal the whole interior of the device.

Step 10

  • Locate and remove the black screw in the center of the motherboard chip.
  • Remove motherboard and replace.

Locate and remove the black screw in the center of the motherboard chip.

Remove motherboard and replace.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    William Tyler Wills

Member since: 09/28/2017

420 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team S2-G1, Nance Fall 2017                        

                                                  Member of USF Tampa, Team S2-G1, Nance Fall 2017 



                    USFT-NANCE-F17S2G1                     


                                            4 Members                     


                                            6 Guides authored