Difficulty

Moderate

Steps

10

Time Required

                          15 minutes

Sections

2

  • Osmo Mobile Handle Disassembly
  • 6 steps
  • Charging Port
  • 4 steps

Flags

0

  • BackDJI Osmo Mobile

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Osmo Mobile Handle Disassembly
  • Remove gimbal from base handle by loosening round plate found at the top of the handle.

Remove gimbal from base handle by loosening round plate found at the top of the handle.

1024

Step 2

  • Use Phillips #00 screwdriver to remove the three screws found on the gimbal stabilizer to detach handle from gimbal.
  • Carefully detach handle from gimbal and disconnect the cable that connects the two.

Use Phillips #00 screwdriver to remove the three screws found on the gimbal stabilizer to detach handle from gimbal.

Carefully detach handle from gimbal and disconnect the cable that connects the two.

Step 3

  • Locate the hex screws found at the top base of the handle, and unscrew using the 1.5mm hex screwdriver.

Locate the hex screws found at the top base of the handle, and unscrew using the 1.5mm hex screwdriver.

Step 4

  • Remove joystick by gently pulling away from handle

Remove joystick by gently pulling away from handle

Step 5

  • Remove the quick release PCBA by locating the connecting wires and release the ribbon cable with tweezers.
  • Use the spudger to pry open and remove the face plate, starting at the back of the handle.

Remove the quick release PCBA by locating the connecting wires and release the ribbon cable with tweezers.

Use the spudger to pry open and remove the face plate, starting at the back of the handle.

Step 6

  • Locate four screws directly on top of handle.
  • Unscrew the silver, bottom two screws, that are closest to the face plate using the 00 screwdriver.
  • Unscrew the black, top two screws, located furthest from the face plate, using the 0 screwdriver.
  • Remove the remaining two screws found on the front of the faceplate.
  • Remove the rest of the face plate shell.

Locate four screws directly on top of handle.

Unscrew the silver, bottom two screws, that are closest to the face plate using the 00 screwdriver.

Unscrew the black, top two screws, located furthest from the face plate, using the 0 screwdriver.

Remove the remaining two screws found on the front of the faceplate.

Remove the rest of the face plate shell.

Step 7

              Charging Port
  • Remove the top left screw on the joystick panel with Phillips #00 screwdriver.
  • Lift faceplate holding joystick module.

Remove the top left screw on the joystick panel with Phillips #00 screwdriver.

Lift faceplate holding joystick module.

Step 8

  • Remove the bottom right screw on the joystick panel with the #00 Phillips screwdriver.

Remove the bottom right screw on the joystick panel with the #00 Phillips screwdriver.

Step 9

  • Hold down the larger of the two ribbon cables, and pull on circuit board with a constant and careful down and out motion.

Hold down the larger of the two ribbon cables, and pull on circuit board with a constant and careful down and out motion.

Step 10

  • Remove the two screws from the green charging module and the two screws on the grey plate and remove from handle.
  • Replace charging module.

Remove the two screws from the green charging module and the two screws on the grey plate and remove from handle.

Replace charging module.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    William Tyler Wills

Member since: 09/28/2017

420 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team S2-G1, Nance Fall 2017                        

                                                  Member of USF Tampa, Team S2-G1, Nance Fall 2017 



                    USFT-NANCE-F17S2G1                     


                                            4 Members                     


                                            6 Guides authored

patchdrury - May 30, 2018

Reply

Where can I buy a replacement port? Can’t find one with google.

John M O’Donovan - Aug 4, 2019

Reply

Where can I buy the part. ?

Nick - Jun 21, 2021

Reply

Which version Osmo Mobile is this for? I need one for ver. 3