Difficulty
Difficult
Steps
9
Time Required
30 minutes
Sections
1
- Fan and Motor
- 9 steps
Flags
Better Introduction
Improve this guide by completing or revising its introduction.
BackOster 16-Speed Blender
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Fan and Motor
- Remove the Blender Container from the Blender Base.
Remove the Blender Container from the Blender Base.
1024
Step 2
- Flip the blender so the bottom is facing you.
Flip the blender so the bottom is facing you.
Step 3
- Unscrew the 16mm screws located on the plastic bottom from the blender base using a Phillips #2 screwdriver.
Unscrew the 16mm screws located on the plastic bottom from the blender base using a Phillips #2 screwdriver.
Step 4
- Remove the plastic bottom from the base of the blender.
Remove the plastic bottom from the base of the blender.
Step 5
- Holding the center of the fan, grip the knob in the center of the top of the blender with a wrench and twist the wrench counterclockwise.
Holding the center of the fan, grip the knob in the center of the top of the blender with a wrench and twist the wrench counterclockwise.
Step 6
- Carefully remove the motor and fan from the base of the blender.
Carefully remove the motor and fan from the base of the blender.
Step 7
- Now, gently pull the white wire that is connected to the base and the motor.
- Be careful, as there is a spring behind the contact points, that might try to shoot out and hurt you.
Now, gently pull the white wire that is connected to the base and the motor.
Be careful, as there is a spring behind the contact points, that might try to shoot out and hurt you.
Step 8
- Now, turn the motor over, and remove the black wire from the motor.
- Again, be warned as the is another spring that wants to shoot out and hurt you here as well.
Now, turn the motor over, and remove the black wire from the motor.
Again, be warned as the is another spring that wants to shoot out and hurt you here as well.
Step 9
- Now de-solder the yellow wire from circuit board. De-solder the wire following these instructions.
- Be careful, as there is another, black wire, nearby that you do not want to de-solder.
Now de-solder the yellow wire from circuit board. De-solder the wire following these instructions.
Be careful, as there is another, black wire, nearby that you do not want to de-solder.
Now the fan and motor are ready for replacement. To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Dana
Member since: 04/14/2014
773 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 12-37, Maness Spring 2014
Member of Cal Poly, Team 12-37, Maness Spring 2014
CPSU-MANESS-S14S12G37
4 Members
5 Guides authored
Arturo Acosta - Jul 29, 2018
Reply
My blender would not blend smoothly. It use to make an unusually loud noise when I put the cup and start the motor. I realized the motor had a “play” making me believe it was not tightened enough. I took a look at the pics on this page and then realized it was assembled wrongly. The white rubber used to absorb the movement was placed after the motor was inserted. Thanks to all who have contributed to this Oster page.
Philip paiva - Jun 7, 2020
Reply
Good day
i took apart my whole oster blender took the electric board out and all the button pieces came out. I have no idea what order they go in or how to put it back. There was a small spring that fell out as well as a Small plastic piece with 2 small springs in it. Can u please help?
