Oster 3905 Retractable Cord Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 hour

Sections

Slot Levers
4 steps
Outer Shell
8 steps
Retractable Cord
8 steps

Flags

BackOster 3905
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Slot Levers

Firmly grip your hand around the slot lever.

Firmly grip your hand around the slot lever.

1024

Step 2

Stabilize the toaster by placing your hand on top.

Stabilize the toaster by placing your hand on top.

Step 3

Forcefully pull the slot lever away from the toaster by keeping parallel to the table.

Forcefully pull the slot lever away from the toaster by keeping parallel to the table.

Step 4

Both slot levers can be removed.

Both slot levers can be removed.

Step 5

              Outer Shell

Place the toaster upside down so the bottom is facing the ceiling.

Place the toaster upside down so the bottom is facing the ceiling.

Step 6

Take off both rubber feet using a small metal spudger.
Wedge a spudger under the feet and pull up to pop off.

Take off both rubber feet using a small metal spudger.

Wedge a spudger under the feet and pull up to pop off.

Step 7

Use a PH#2 screw bit to remove eight 12mm screws that are located around the perimeter.
There are two screws under the rubber feet.

Use a PH#2 screw bit to remove eight 12mm screws that are located around the perimeter.

There are two screws under the rubber feet.

Step 8

Place the toaster right side up.

Place the toaster right side up.

Step 9

Grab the outer shell firmly and pull up towards the face of the toaster.

Grab the outer shell firmly and pull up towards the face of the toaster.

Step 10

For this part, you might need to wiggle the toaster to get the outer shell off.
The shell will not completely come off until the motherboard is removed in the next step.

For this part, you might need to wiggle the toaster to get the outer shell off.

The shell will not completely come off until the motherboard is removed in the next step.

Step 11

Use a J1 screw bit to unscrew eight 8mm screws from the motherboard.

Use a J1 screw bit to unscrew eight 8mm screws from the motherboard.

Step 12

Take out the grey “cancel” and “bagel” buttons from the shell.

Take out the grey “cancel” and “bagel” buttons from the shell.

Step 13

              Retractable Cord

Rotate the toaster so that the back is facing towards you.

Rotate the toaster so that the back is facing towards you.

Step 14

Use the PH#1 bit to remove one 8mm screw located above the wire on the casing.
Then use the same screw bit to remove two 10mm screws found at the bottom.

Use the PH#1 bit to remove one 8mm screw located above the wire on the casing.

Then use the same screw bit to remove two 10mm screws found at the bottom.

Step 15

Using the metal spudger, pry next to the black clip found at the base of the toaster and the casing.
Push down to separate the casing from the toaster.

Using the metal spudger, pry next to the black clip found at the base of the toaster and the casing.

Push down to separate the casing from the toaster.

Step 16

Gently tilt the casing towards the toaster as you pull up from the base.

Gently tilt the casing towards the toaster as you pull up from the base.

Step 17

Use the PH#1 bit to remove the three 8mm screws located on the back side of the casing.

Use the PH#1 bit to remove the three 8mm screws located on the back side of the casing.

Step 18

When opening the casing a metal spring may suddenly pop out.
Use the metal spudger to pry open the two halves of the casing.
If you are having some trouble only using the metal spudger do not be afraid of using your fingers to pry the casing apart.

When opening the casing a metal spring may suddenly pop out.

Use the metal spudger to pry open the two halves of the casing.

If you are having some trouble only using the metal spudger do not be afraid of using your fingers to pry the casing apart.

Step 19

Carefully remove the spool keeping your fingers on either side of the casing.
Tape down the metal spring to keep it from unraveling out of place.

Carefully remove the spool keeping your fingers on either side of the casing.

Tape down the metal spring to keep it from unraveling out of place.

Step 20

Carefully unwind the power cord from the spool.

Carefully unwind the power cord from the spool.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Adam Dierkes

Member since: 09/12/2016

140 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       CSU Fullerton, Team 2-1, Bruce Fall 2016                        

                                                  Member of CSU Fullerton, Team 2-1, Bruce Fall 2016 



                    CSUF-BRUCE-F16S2G1                     


                                            5 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team