Oster 6329 Power Cord Replacement Repair Guide

Difficulty

Moderate

Steps

12

Time Required

                          30 - 35 minutes            

Sections

2

• Outer Shell Removal
• 5 steps
• Power Cord
• 7 steps

Flags

0

• BackOster 6329

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Outer Shell Removal               

• Using the Phillips-head #2 screwdriver, unscrew the three 1cm Phillips-head screws on the plastic base of the toaster to separate the outer metal shell from the plastic base.

Using the Phillips-head #2 screwdriver, unscrew the three 1cm Phillips-head screws on the plastic base of the toaster to separate the outer metal shell from the plastic base.

1024

Step 2

• Push the plastic push-down handle down and pull the plastic handle straight from metal arm.

Push the plastic push-down handle down and pull the plastic handle straight from metal arm.

Step 3

• Loosen the outer metal shell from the plastic base by holding the plastic base while pulling up on the metal shell.
• Only lift the outer shell a little so as not to disconnect the cables that connect the circuit board.

Loosen the outer metal shell from the plastic base by holding the plastic base while pulling up on the metal shell.

Only lift the outer shell a little so as not to disconnect the cables that connect the circuit board.

Step 4

• Disconnect the cable clips from the circuit board using the tweezers to free the outer metal shell from the plastic base.

Disconnect the cable clips from the circuit board using the tweezers to free the outer metal shell from the plastic base.

Step 5

• Lift the top outer metal shell.
• Carefully lift the outer metal shell at an angle so as not to damage the components in the front of the toaster.

Lift the top outer metal shell.

Carefully lift the outer metal shell at an angle so as not to damage the components in the front of the toaster.

Step 6

              Power Cord               

• Using a flat-head screwdriver, pry the power cord from the base of the toaster.

Using a flat-head screwdriver, pry the power cord from the base of the toaster.

Step 7

• Using a flat-head screwdriver, pry the white wire from the base.

Using a flat-head screwdriver, pry the white wire from the base.

Step 8

• Locate the circuit board at the front of the toaster where the power cord and white wire meet.
• Pull the circuit board up and out to free the circuit board from the body of the toaster.
• It is tightly fit and may take moderate force to remove.

Locate the circuit board at the front of the toaster where the power cord and white wire meet.

Pull the circuit board up and out to free the circuit board from the body of the toaster.

It is tightly fit and may take moderate force to remove.

Step 9

• Desolder the power cord from the circuit board at the locations show in the diagram.
• For soldering instructions see the iFixit Soldering Guide.
• The wires should be free from board when un-soldering is complete.

Desolder the power cord from the circuit board at the locations show in the diagram.

For soldering instructions see the iFixit Soldering Guide.

The wires should be free from board when un-soldering is complete.

Step 10

• Unscrew the two 1.5cm Phillips-head screws at the back of the toaster that are holding the power cord in place to remove the retaining clip.
• Remove the plastic retaining clip that is holding the cord in place.

Unscrew the two 1.5cm Phillips-head screws at the back of the toaster that are holding the power cord in place to remove the retaining clip.

Remove the plastic retaining clip that is holding the cord in place.

Step 11

• Untie the knot in the power cord.

Untie the knot in the power cord.

Step 12

• Pull the cord from the base to remove the cable.

Pull the cord from the base to remove the cable.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors 

                    Timothy Grijalva                     

Member since: 01/31/2014

210 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       Cal Poly, Team 13-15, Regan Winter 2014                        

                                                  Member of Cal Poly, Team 13-15, Regan Winter 2014 



                    CPSU-REGAN-W14S13G15                     


                                            5 Members                     


                                            6 Guides authored