Difficulty
Difficult
Steps
12
Time Required
25 - 30 minutes
Sections
2
- Panel Removal
- 9 steps
- Button
- 3 steps
Flags
1
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
BackOzeri Pronto ZK14-S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Panel Removal
- Twist the plastic plate slowly to the left to pull it away.
Twist the plastic plate slowly to the left to pull it away.
1024
Step 2
- Pry off the sticker at the bottom where the “Ozeri” logo is to reveal a screw. The sticker does not need to be completely removed for the next step.
Pry off the sticker at the bottom where the “Ozeri” logo is to reveal a screw. The sticker does not need to be completely removed for the next step.
Step 3
- Using the 2.0 Flathead screwdriver, remove the 9.50 mm Phillips head screw under the sticker.
Using the 2.0 Flathead screwdriver, remove the 9.50 mm Phillips head screw under the sticker.
Step 4
- Using the 2.0 Flathead screwdriver, remove the two 18.76 mm Phillips head screws in the plate stand.
Using the 2.0 Flathead screwdriver, remove the two 18.76 mm Phillips head screws in the plate stand.
Step 5
- Using the 2.0 Flathead screwdriver, remove the 9.44 mm Phillips head screw on the end opposite of the LCD screen.
Using the 2.0 Flathead screwdriver, remove the 9.44 mm Phillips head screw on the end opposite of the LCD screen.
Step 6
- Turn the device over so the back panel is facing up.
Turn the device over so the back panel is facing up.
Step 7
- Using the plastic opening tool, pry off each of the two rubber stubs on the right side and the two stubs on the left side of bottom of the device.
Using the plastic opening tool, pry off each of the two rubber stubs on the right side and the two stubs on the left side of bottom of the device.
Step 8
- Using the 2.0 Flathead screwdriver, remove of the four 9.46 mm Phillips head screws under the removed stubs.
Using the 2.0 Flathead screwdriver, remove of the four 9.46 mm Phillips head screws under the removed stubs.
Step 9
- Pry apart the two panels to separate them from each other.
- Flip the device over so the LCD is facing up. Flip the front panel over on its side.
- Be careful when separating the panels to avoid damaging the wires they are connected by.
Pry apart the two panels to separate them from each other.
Flip the device over so the LCD is facing up. Flip the front panel over on its side.
Be careful when separating the panels to avoid damaging the wires they are connected by.
Step 10
Button
- Using the 2.0 Flathead screwdriver, remove the two 7.34 mm screws on of the smaller motherboards.
Using the 2.0 Flathead screwdriver, remove the two 7.34 mm screws on of the smaller motherboards.
Step 11
- Desolder the four posts in the center of the motherboard.
- Use caution when handling the soldering since it can get very hot.
Desolder the four posts in the center of the motherboard.
Use caution when handling the soldering since it can get very hot.
Step 12
- Desolder the two clips in the center of the motherboard.
- Use caution when handling the soldering iron since it can get very hot.
- Note: Repeat steps 13 and 14 to remove the other button from its motherboard.
Desolder the two clips in the center of the motherboard.
Use caution when handling the soldering iron since it can get very hot.
Note: Repeat steps 13 and 14 to remove the other button from its motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 1 other contributor
Oneika White
Member since: 10/01/2015
664 Reputation
4 Guides authored
Badges:
14
+11 more badges
Team
USF Tampa, Team 1-4, Leahy Fall 2015
Member of USF Tampa, Team 1-4, Leahy Fall 2015
USFT-LEAHY-F15S1G4
4 Members
5 Guides authored
