Palm Treo 650 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          15 minutes            

Sections

4

• Battery and Stylus
• 3 steps
• Case
• 4 steps
• Motherboard
• 2 steps
• LCD Screen
• 2 steps

Flags

3

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackPalm Treo 650

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery and Stylus               

• Position the phone so the screen faces down.
• Remove the stylus found on the back of the phone.

Position the phone so the screen faces down.

Remove the stylus found on the back of the phone.

1024

Step 2

• To remove the battery cover, hold down the button in the middle of the phone’s back.
• Slide the cover down to remove it, and set the cover aside.

To remove the battery cover, hold down the button in the middle of the phone’s back.

Slide the cover down to remove it, and set the cover aside.

Step 3

• Lift the edge of the battery, separating contact points, and pull out as pictured.

Lift the edge of the battery, separating contact points, and pull out as pictured.

Step 4

              Case               

• Remove the round rubber cover on the back of the phone located immediately below the antenna.
• This will uncover a screw that will be removed in the next step.

Remove the round rubber cover on the back of the phone located immediately below the antenna.

This will uncover a screw that will be removed in the next step.

Step 5

• Remove the six 6.9 mm screws as pictured with a T5 Torx screwdriver.
• Remove the single 9.8 mm screw next to the antenna on the back plate using a Phillips #00 screwdriver.

Remove the six 6.9 mm screws as pictured with a T5 Torx screwdriver.

Remove the single 9.8 mm screw next to the antenna on the back plate using a Phillips #00 screwdriver.

Step 6

• Remove the antenna.

Remove the antenna.

Step 7

• Pry the back cover off using an iFixIt opening tool.
• The back cover is attached by several small clips on the inside.

Pry the back cover off using an iFixIt opening tool.

The back cover is attached by several small clips on the inside.

Step 8

              Motherboard               

• Disconnect the ribbon cable before removing the motherboard.
• Unclip the gray tab.
• Pull out the orange ribbon cable.

Disconnect the ribbon cable before removing the motherboard.

Unclip the gray tab.

Pull out the orange ribbon cable.

Step 9

• Pull off the motherboard.

Pull off the motherboard.

Step 10

              LCD Screen               

• Lift up the LCD screen so that the ribbon strip connecting it to the motherboard can be accessed.
• Only lift the screen high enough to access the ribbon cable.

Lift up the LCD screen so that the ribbon strip connecting it to the motherboard can be accessed.

Only lift the screen high enough to access the ribbon cable.

Step 11

• Unclip the gray tab.
• Pull out the orange ribbon strip.
• Remove the LCD screen.

Pull out the orange ribbon strip.

Remove the LCD screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 9 other contributors 

                    cgood                     

Member since: 10/28/2009

122 Reputation

                                      7 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       Cal Poly, Team 19-3, Maness Fall 2009                        

                                                  Member of Cal Poly, Team 19-3, Maness Fall 2009 



                    CPSU-MANESS-F09S19G3                     


                                            4 Members                     


                                            18 Guides authored