Difficulty
Very easy
Steps
14
Time Required
2 minutes
Sections
5
- Battery and Stylus
- 3 steps
- Case
- 4 steps
- Motherboard
- 2 steps
- Keyboard
- 3 steps
- Microphone
- 2 steps
Flags
3
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
Grammar Police
Embrace your inner English teacher and help improve this guide’s grammar!
BackPalm Treo 650
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery and Stylus
- Position the phone so the screen faces down.
- Remove the stylus found on the back of the phone.
Position the phone so the screen faces down.
Remove the stylus found on the back of the phone.
1024
Step 2
- To remove the battery cover, hold down the button in the middle of the phone’s back.
- Slide the cover down to remove it, and set the cover aside.
To remove the battery cover, hold down the button in the middle of the phone’s back.
Slide the cover down to remove it, and set the cover aside.
Step 3
- Lift the edge of the battery, separating contact points, and pull out as pictured.
Lift the edge of the battery, separating contact points, and pull out as pictured.
Step 4
Case
- Remove the round rubber cover on the back of the phone located immediately below the antenna.
- This will uncover a screw that will be removed in the next step.
Remove the round rubber cover on the back of the phone located immediately below the antenna.
This will uncover a screw that will be removed in the next step.
Step 5
- Remove the six 6.9 mm screws as pictured with a T5 Torx screwdriver.
- Remove the single 9.8 mm screw next to the antenna on the back plate using a Phillips #00 screwdriver.
Remove the six 6.9 mm screws as pictured with a T5 Torx screwdriver.
Remove the single 9.8 mm screw next to the antenna on the back plate using a Phillips #00 screwdriver.
Step 6
- Remove the antenna.
Remove the antenna.
Step 7
- Pry the back cover off using an iFixIt opening tool.
- The back cover is attached by several small clips on the inside.
Pry the back cover off using an iFixIt opening tool.
The back cover is attached by several small clips on the inside.
Step 8
Motherboard
- Disconnect the ribbon cable before removing the motherboard.
- Unclip the gray tab.
- Pull out the orange ribbon cable.
Disconnect the ribbon cable before removing the motherboard.
Unclip the gray tab.
Pull out the orange ribbon cable.
Step 9
- Pull off the motherboard.
Pull off the motherboard.
Step 10
Keyboard
- Unscrew the two 3.2 mm screws with a Phillips #00 screwdriver.
Unscrew the two 3.2 mm screws with a Phillips #00 screwdriver.
Step 11
- Pull off the circuit board.
Pull off the circuit board.
Step 12
- Remove the keypad for cleaning or replacing.
Remove the keypad for cleaning or replacing.
Step 13
Microphone
- Place the circuit board with the microphone facing up.
Place the circuit board with the microphone facing up.
Step 14
- The microphone should be able to pop off easily using your finger.
The microphone should be able to pop off easily using your finger.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
cgood
Member since: 10/28/2009
122 Reputation
7 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 19-3, Maness Fall 2009
Member of Cal Poly, Team 19-3, Maness Fall 2009
CPSU-MANESS-F09S19G3
4 Members
18 Guides authored
