Difficulty

Moderate

Steps

11

Time Required

                          10 - 15 minutes

Sections

5

  • Back Panel
  • 5 steps
  • Battery Pack
  • 1 step
  • Motherboard
  • 2 steps
  • Display
  • 1 step
  • Buttons and Connector Assembly
  • 2 steps

Flags

0

  • BackPalm TX

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Back Panel
  • Orient the device so that the display faces forward.
  • Remove the stylus from the right side.

Orient the device so that the display faces forward.

Remove the stylus from the right side.

1024

Step 2

  • Turn over the device so that the back panel faces forward.
  • Use a T5 Torx screwdriver to remove the four 6.35mm corner screws.

Turn over the device so that the back panel faces forward.

Use a T5 Torx screwdriver to remove the four 6.35mm corner screws.

Step 3

  • Rotate the device so that the display faces forward.
  • Insert a plastic opening tool with the angled tip pointing downward into the crevice on the left side of the device.
  • Pry along the crevice to loosen the back panel.
  • Repeat this process for the right side.

Rotate the device so that the display faces forward.

Insert a plastic opening tool with the angled tip pointing downward into the crevice on the left side of the device.

Pry along the crevice to loosen the back panel.

Repeat this process for the right side.

Step 4

  • Carefully pry the back panel to open the device.
  • Be careful not to break the wire that connects the battery pack to the motherboard.
  • When reassembling, snap the back panel back into place and then insert the top cover.

Carefully pry the back panel to open the device.

Be careful not to break the wire that connects the battery pack to the motherboard.

When reassembling, snap the back panel back into place and then insert the top cover.

Step 5

  • Use a plastic opening tool to peel the battery pack from the back panel.
  • The battery pack is glued to the back panel so removing it may require considerable effort.

Use a plastic opening tool to peel the battery pack from the back panel.

The battery pack is glued to the back panel so removing it may require considerable effort.

Step 6

              Battery Pack
  • Use a soldering iron to disconnect the battery wires from the motherboard.
  • For soldering instructions, you can view the Soldering Guide.

Use a soldering iron to disconnect the battery wires from the motherboard.

For soldering instructions, you can view the Soldering Guide.

Step 7

              Motherboard
  • Pull straight up on the ribbon cables located on the bottom right of the motherboard to disconnect them.

Pull straight up on the ribbon cables located on the bottom right of the motherboard to disconnect them.

Step 8

  • Lift the mother board out of the device.
  • A weak adhesive attaches the motherboard to the device.
  • The red wire in the picture will not be attached to your device at this point.

Lift the mother board out of the device.

A weak adhesive attaches the motherboard to the device.

The red wire in the picture will not be attached to your device at this point.

Step 9

              Display
  • Orient the device sideways, as shown in the picture.
  • Lightly push the front of the display to separate it from the front panel.
  • The battery in the picture will not be attached to the device at this point.

Orient the device sideways, as shown in the picture.

Lightly push the front of the display to separate it from the front panel.

The battery in the picture will not be attached to the device at this point.

Step 10

              Buttons and Connector Assembly
  • Use a T5 Torx screwdriver to remove the 7.75mm screws at the bottom of the device.
  • It may take some manipulation to remove the screws.

Use a T5 Torx screwdriver to remove the 7.75mm screws at the bottom of the device.

It may take some manipulation to remove the screws.

Step 11

  • Lift the button and connector assembly from the front panel.

Lift the button and connector assembly from the front panel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors 


                    Spencer Lewson

Member since: 01/19/2011

778 Reputation

                                      6 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 1-15, Amido Winter 2011                        

                                                  Member of Cal Poly, Team 1-15, Amido Winter 2011 



                    CPSU-AMIDO-W11S1G15                     


                                            4 Members                     


                                            7 Guides authored

Sean Madawala - Sep 18, 2020

Reply

Where can you buy one of these?