Panasonic Lumix Dmc Fh25 Page Lens Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

13

Time Required

                          15 minutes            

Sections

4

• Back Case
• 3 steps
• Front Case
• 3 steps
• LCD Screen
• 3 steps
• Lens Assembly
• 4 steps

Flags

0

• BackPanasonic Lumix DMC-FH25

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Back Case               

• Remove 5 screws attached to the back case using a 00 Phillips head screwdriver.

Remove 5 screws attached to the back case using a 00 Phillips head screwdriver.

1024

Step 2

• Using your hands and a pry tool, lever the back case off.

Using your hands and a pry tool, lever the back case off.

Step 3

• Remove the back case.

Remove the back case.

Step 4

              Front Case               

• Remove four screws on the front case using a 00 Phillips head screwdriver. Two will be on the side with the camera strap, one on the bottom, and one on the side opposing the camera strap. They will be in pairs, one screw holding the front case and one screw holding the back case.

Remove four screws on the front case using a 00 Phillips head screwdriver. Two will be on the side with the camera strap, one on the bottom, and one on the side opposing the camera strap. They will be in pairs, one screw holding the front case and one screw holding the back case.

Step 5

• Using a plastic opening tool and your hands, pull the front case loose from the camera.

Using a plastic opening tool and your hands, pull the front case loose from the camera.

Step 6

• Remove the front case from the camera.

Remove the front case from the camera.

Step 7

              LCD Screen               

• Using a 00 Phillips head screwdriver, remove a screw from the top right corner of the screen.
• Lift the screen, being careful not to tear the ribbon cables on the right side.

Using a 00 Phillips head screwdriver, remove a screw from the top right corner of the screen.

Lift the screen, being careful not to tear the ribbon cables on the right side.

Step 8

• Access the ribbon cables by removing the green button receiver panel using a plastic opening tool. There is a white panel beneath. Carefully remove this using a plastic opening tool. The white panel may require some elbow grease to get it off, and the panel may make a snapping sound as it comes off.

Access the ribbon cables by removing the green button receiver panel using a plastic opening tool. There is a white panel beneath. Carefully remove this using a plastic opening tool. The white panel may require some elbow grease to get it off, and the panel may make a snapping sound as it comes off.

Step 9

• One of the ribbon cables will be housed behind the screen and the other will be under the panels. Gently pull each free from the housing and remove the screen.

One of the ribbon cables will be housed behind the screen and the other will be under the panels. Gently pull each free from the housing and remove the screen.

Step 10

              Lens Assembly               

• Under the screen is a silver panel. Remove three screws using a 00 philips screwdriver and take the plate off.

Under the screen is a silver panel. Remove three screws using a 00 philips screwdriver and take the plate off.

Step 11

• Remove the silver panel with the buttons and flash battery from the top of the camera. The silver tripod socket may fall out. Do not be alarmed and don’t put it back in.

Remove the silver panel with the buttons and flash battery from the top of the camera. The silver tripod socket may fall out. Do not be alarmed and don’t put it back in.

Step 12

• Use the pry tool to lift the latches holding the ribbon cables in place. Gently tug on them, careful not to break them. The top ribbon cable will take more effort.

Use the pry tool to lift the latches holding the ribbon cables in place. Gently tug on them, careful not to break them. The top ribbon cable will take more effort.

Step 13

• Gently remove the lens assembly. It should slide out cleanly.

Gently remove the lens assembly. It should slide out cleanly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Janice Weldon                     

Member since: 03/07/2017

591 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       UMass Dartmouth, Team S6-G6, Isaacson Spring 2017                        

                                                  Member of UMass Dartmouth, Team S6-G6, Isaacson Spring 2017 



                    UMASSD-ISAACSON-S17S6G6                     


                                            3 Members                     


                                            10 Guides authored                     

henry vargas pineda - Nov 1, 2019

Reply

Hi I disassemble my câmera lens but I don’t know How to reassamble It again,can you Help me? can I send you Fotos?