Panasonic Lumix Dmc Fx01 On Off And Settings Button Cover Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 - 45 minutes

Sections

Battery
3 steps
Rear Casing
6 steps
LCD Screen
2 steps
On/ Off Button and Settings Button
6 steps

Flags

BackPanasonic Lumix DMC-FX01
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Battery

Locate the memory card and battery card latch on the bottom of the camera.
Slide the latch to the open position.

Locate the memory card and battery card latch on the bottom of the camera.

Slide the latch to the open position.

1024

Step 2

Open the battery latch, and slide the battery release lever to the right.

Open the battery latch, and slide the battery release lever to the right.

Step 3

Remove the battery from the camera.

Remove the battery from the camera.

Step 4

              Rear Casing

Remove the three 4.6 mm screws on the bottom of the camera using a Phillips #00 screwdriver.

Remove the three 4.6 mm screws on the bottom of the camera using a Phillips #00 screwdriver.

Step 5

Remove the single 3.2 mm screw on the left side of the camera using a Phillips #00 screwdriver.

Remove the single 3.2 mm screw on the left side of the camera using a Phillips #00 screwdriver.

Step 6

Remove the left side casing.

Remove the left side casing.

Step 7

Remove the two 3.2 mm screws on the right side of the camera using a Phillips #00 screwdriver.

Remove the two 3.2 mm screws on the right side of the camera using a Phillips #00 screwdriver.

Step 8

Remove the bottom right panel.

Remove the bottom right panel.

Step 9

Gently remove the back casing.
Start at the bottom and carefully pry towards the top to get this piece free.

Gently remove the back casing.

Start at the bottom and carefully pry towards the top to get this piece free.

Step 10

              LCD Screen

Gently lift up the LCD screen.
Using a plastic prying tool, flip up the latch that holds the thin ribbon in place.
It should fall out on its own or with a gentle tug.

Gently lift up the LCD screen.

Using a plastic prying tool, flip up the latch that holds the thin ribbon in place.

It should fall out on its own or with a gentle tug.

Step 11

Gently tug the thicker ribbon to remove it from its housing.

Gently tug the thicker ribbon to remove it from its housing.

Step 12

              On/ Off Button and Settings Button

Carefully remove the upper assembly, which houses the buttons and the flash battery.

Carefully remove the upper assembly, which houses the buttons and the flash battery.

Step 13

Remove the two 3mm screws.

Remove the two 3mm screws.

Step 14

Pry bars back gently as shown.
Fingers can be used but tool is shown for clarity.

Pry bars back gently as shown.

Fingers can be used but tool is shown for clarity.

Step 15

After, releasing all the components, gently remove the flash assembly from the casing.

After, releasing all the components, gently remove the flash assembly from the casing.

Step 16

Remove the 1.2 mm screw from the settings wheel.

Remove the 1.2 mm screw from the settings wheel.

Step 17

Replace buttons.
Replace the “On/ Off” button with the prongs facing away from the flash.

Replace buttons.

Replace the “On/ Off” button with the prongs facing away from the flash.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Andrew

Member since: 10/11/2010

396 Reputation

                                      4 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team 9-22, Regan Fall 2010                        

                                                  Member of Cal Poly, Team 9-22, Regan Fall 2010 



                    CPSU-REGAN-F10S9G22                     


                                            4 Members                     


                                            8 Guides authored

Ricardo Britto - Jan 16, 2017

Olá ! Sugiro ter cuidado com a carga do capacitor do flash, melhor descarrega-lo com auxílio de uma lâmpada ou resistor

para evitar um choque elétrico.

What you need#

Team#

What you need

Team