Difficulty
Moderate
Steps
9
Time Required
30 minutes
Sections
1
- LCD
- 9 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackPanasonic Lumix DMC-FZ35
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Clear compartment
- Remove the battery and memory card from the unit.
Remove the battery and memory card from the unit.
1024
Step 2
Remove side screws
- Remove 1 screw (0.4mm) from left side of unit
- Remove 1 screw (0.4mm) from right side of unit near Strap bar.
- Remove 1 screw (0.6mm) from right side of unit next to usb door
Remove 1 screw (0.4mm) from left side of unit
Remove 1 screw (0.4mm) from right side of unit near Strap bar.
Remove 1 screw (0.6mm) from right side of unit next to usb door
Step 3
Remove Screws from Bottom
- Remove 3 Screws from bottom of unit
- Remove 2 (0.6mm) screws next to door
- Remove 1 (0.4mm) screw opposite of door
Remove 3 Screws from bottom of unit
Remove 2 (0.6mm) screws next to door
Remove 1 (0.4mm) screw opposite of door
Step 4
Remove top screw
- Raise the Pop-Up flash by pushing the flash button.
- Remove the screw (0.6mm) from underneath the flash assembly.
Raise the Pop-Up flash by pushing the flash button.
Remove the screw (0.6mm) from underneath the flash assembly.
Step 5
Accessing the flex cables
- Please be careful. Do not lift the cover fully because it is still attached to the Main Board via flex cables.
- Lift the cover slightly as shown in picture # 1
- Tilt the back cover as shown in picture #2. Be careful because the flex cables are still attached.
Please be careful. Do not lift the cover fully because it is still attached to the Main Board via flex cables.
Lift the cover slightly as shown in picture # 1
Tilt the back cover as shown in picture #2. Be careful because the flex cables are still attached.
Step 6
Release the Flex cables
- Flip up LCD cable clamp with a spudger or other tool.
- Flip up backlite cable clamp with a spudger or other tool
- Removal of the mic wire is optional. My suggestion is to leave it attached. The mic can get damaged if you pull on the wire.
Flip up LCD cable clamp with a spudger or other tool.
Flip up backlite cable clamp with a spudger or other tool
Removal of the mic wire is optional. My suggestion is to leave it attached. The mic can get damaged if you pull on the wire.
Step 7
Remove the mic
- Remove the 2 screws (0.4mm) that are holding the mic assembly
- Next step (shown in picture #2) remove the metal mic hold part.
- Next step (shown in picture #3) use a spudger to pry off the mic. Careful not to damage the wiring.
Remove the 2 screws (0.4mm) that are holding the mic assembly
Next step (shown in picture #2) remove the metal mic hold part.
Next step (shown in picture #3) use a spudger to pry off the mic. Careful not to damage the wiring.
Step 8
Remove the LCD
- Release the hold clips that hold the LCD retainer in place.
- Remove the LCD metal retainer plate as shown in picture #2
- Remove the LCD as shown in picture # 3
Release the hold clips that hold the LCD retainer in place.
Remove the LCD metal retainer plate as shown in picture #2
Remove the LCD as shown in picture # 3
Step 9
Swap out Old LCD
- Swap out your old LCD with the new one.
- If your backlite is ok you can buy only the LCD Display. But it is easier to purchase the LCD with the backlite attached. Replacement LCD Display VYQ5034
Swap out your old LCD with the new one.
If your backlite is ok you can buy only the LCD Display. But it is easier to purchase the LCD with the backlite attached. Replacement LCD Display VYQ5034
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 1 other contributor
Sales Cameraparts4you
Member since: 07/01/2016
3,042 Reputation
20 Guides authored
Badges:
17
+14 more badges
