Difficulty
Moderate
Steps
10
Time Required
15 minutes
Sections
3
- Battery
- 2 steps
- Back Cover
- 7 steps
- Back Panel Buttons
- 1 step
Flags
0
BackPanasonic Lumix DMC-GF2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- On the bottom of the camera, use your finger to push the lock button to the open position which will cause the hinged door to swing open.
On the bottom of the camera, use your finger to push the lock button to the open position which will cause the hinged door to swing open.
1024
Step 2
- Push the small black tab that holds the battery with your finger to release the battery.
- Use your fingers to pull the battery out of the camera.
Push the small black tab that holds the battery with your finger to release the battery.
Use your fingers to pull the battery out of the camera.
Step 3
Back Cover
- Using a Phillips #00 screwdriver, remove six 2.69mm, silver screws located on the two short sides of the camera and the bottom side.
Using a Phillips #00 screwdriver, remove six 2.69mm, silver screws located on the two short sides of the camera and the bottom side.
Step 4
- Gently lift up the back cover to access the ZIF connectors for the blue and yellow ribbons.
- To unlock the ZIF connectors, gently push the black portion of the lock from a flat position to an upright position using a spudger.
- Take caution not to rip the ribbons out of the ZIF connectors when lifting the back panel.
Gently lift up the back cover to access the ZIF connectors for the blue and yellow ribbons.
To unlock the ZIF connectors, gently push the black portion of the lock from a flat position to an upright position using a spudger.
Take caution not to rip the ribbons out of the ZIF connectors when lifting the back panel.
Step 5
- Gently push the blue and yellow ribbons out of the unlocked ZIF connectors using your fingers.
Gently push the blue and yellow ribbons out of the unlocked ZIF connectors using your fingers.
Step 6
- Using a Phillips #00 screwdriver, remove the 3.5 mm silver screw from the upper left hand corner of the back cover.
Using a Phillips #00 screwdriver, remove the 3.5 mm silver screw from the upper left hand corner of the back cover.
Step 7
- Using a spudger, lift up and remove the plastic cover piece from the back cover.
- Plastic cover may fall off without prying.
Using a spudger, lift up and remove the plastic cover piece from the back cover.
Plastic cover may fall off without prying.
Step 8
- Using a Phillips #00 screwdriver, remove the 2.69 mm silver screw located beneath the plastic piece that was previously removed.
Using a Phillips #00 screwdriver, remove the 2.69 mm silver screw located beneath the plastic piece that was previously removed.
Step 9
- Using a spudger, lift up and separate the heavier metal cover from the light, plastic back cover.
- Metal cover may fall off without prying.
Using a spudger, lift up and separate the heavier metal cover from the light, plastic back cover.
Metal cover may fall off without prying.
Step 10
Back Panel Buttons
- Push on the back panel buttons from the frontside of the back cover.
- There might be some adhesives holding the back panel buttons to the cover. Extra force may be necessary.
Push on the back panel buttons from the frontside of the back cover.
There might be some adhesives holding the back panel buttons to the cover. Extra force may be necessary.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Kingsley East
Member since: 10/30/2016
456 Reputation
4 Guides authored
Badges:
9
+6 more badges
Team
Baylor, Team 5-9, Williams Fall 2016
Member of Baylor, Team 5-9, Williams Fall 2016
BU-WILLIAMS-F16S5G9
3 Members
10 Guides authored
