Featured
Featured Guide
Difficulty
Moderate
Steps
19
Time Required
25 minutes
Sections
4
- Back Cover
- 7 steps
- button board
- 4 steps
- Camera Lens Assembly
- 4 steps
- AV port circuit board
- 4 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackPanasonic Lumix DMC-TZ5
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove the battery and memory card from the device.
Remove the battery and memory card from the device.
1024
Step 2
- Remove 4 screws from the right side of the camera.
- There are two 3.4mm screws at the top.
- There are two 2.2mm screws at the bottom.
Remove 4 screws from the right side of the camera.
There are two 3.4mm screws at the top.
There are two 2.2mm screws at the bottom.
Step 3
- Remove the single 3.4mm screw on the left side of the camera.
Remove the single 3.4mm screw on the left side of the camera.
Step 4
- Remove 5 screws from the base of the camera.
- There are two 2.2mm screws next to the battery compartment.
- There are three 4mm screws around the tripod mount.
Remove 5 screws from the base of the camera.
There are two 2.2mm screws next to the battery compartment.
There are three 4mm screws around the tripod mount.
Step 5
- Slowly slide the back cover away from the device
- The back casing is held in place by two ribbon cables. Do not pull the back cover too far from the camera.
Slowly slide the back cover away from the device
The back casing is held in place by two ribbon cables. Do not pull the back cover too far from the camera.
Step 6
- Detach both ribbon cables using a spudger.
- Use the tip of the spudger to lift the black clip upward, unlocking the ribbon cable.
Detach both ribbon cables using a spudger.
Use the tip of the spudger to lift the black clip upward, unlocking the ribbon cable.
Step 7
- Remove the back casing from the camera.
Remove the back casing from the camera.
Step 8
button board
- Use the spudger to remove the ribbon cable connecting the lens casing to the circuit board by lifting up the black clip.
- Carefully remove the function switch cover. This unit snaps on and off.
Use the spudger to remove the ribbon cable connecting the lens casing to the circuit board by lifting up the black clip.
Carefully remove the function switch cover. This unit snaps on and off.
Step 9
- Carefully unsnap the front logic board from the rear logic board using a spudger.
Carefully unsnap the front logic board from the rear logic board using a spudger.
Step 10
- Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera.
Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera.
Step 11
- Remove the ribbon cable from the top connection panel by unlocking the black clip with a spudger.
- This leaves you with the logic board and the top connection panel separate and free from the camera
Remove the ribbon cable from the top connection panel by unlocking the black clip with a spudger.
This leaves you with the logic board and the top connection panel separate and free from the camera
Step 12
Camera Lens Assembly
- Use a spudger to detach the ribbon cable from the circuit board. Lift the black clip up to unlock it as before.
Use a spudger to detach the ribbon cable from the circuit board. Lift the black clip up to unlock it as before.
Step 13
- Remove the 3 screws holding the lens assembly in place.
- The two screws on the left are 4.5mm with washers.
- The single screw on the right is 4mm.
Remove the 3 screws holding the lens assembly in place.
The two screws on the left are 4.5mm with washers.
The single screw on the right is 4mm.
Step 14
- Push the lens assembly slightly toward the circuit board, and pull the left side out of the casing first. You will have to wiggle this out gently.
Push the lens assembly slightly toward the circuit board, and pull the left side out of the casing first. You will have to wiggle this out gently.
Step 15
- Remove the entire assembly out of the casing.
- The ribbons on the left and bottom of the assembly simply rest on the camera housing.
Remove the entire assembly out of the casing.
The ribbons on the left and bottom of the assembly simply rest on the camera housing.
Step 16
AV port circuit board
- Use the spudger to unclip the top ribbon cable from the circuit board.
Use the spudger to unclip the top ribbon cable from the circuit board.
Step 17
- Remove the single 2mm screw in the bottom right corner of the circuit board
Remove the single 2mm screw in the bottom right corner of the circuit board
Step 18
- Gently slide the circuit board out away from the port connections. Pull it toward where the lens used to be. Some wiggling may be necessary to remove.
- The circuit board is fitted into slots attached to the side of the camera. Do not angle upwards to remove.
Gently slide the circuit board out away from the port connections. Pull it toward where the lens used to be. Some wiggling may be necessary to remove.
The circuit board is fitted into slots attached to the side of the camera. Do not angle upwards to remove.
Step 19
- Take note of how the slots fit into the circuit board for easy replacement.
Take note of how the slots fit into the circuit board for easy replacement.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 5 other contributors
Kevin Lufkin
Member since: 10/11/2010
158 Reputation
2 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 9-21, Regan Fall 2010
Member of Cal Poly, Team 9-21, Regan Fall 2010
CPSU-REGAN-F10S9G21
4 Members
14 Guides authored
Janx38 - Mar 21, 2016
Reply
Where can I buy this part? Thanks!
