Panasonic Lumix Dmc Zs25 Flash Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Flash
20 steps

Flags

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

BackPanasonic Lumix DMC-ZS25
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Flash

Using a small screwdriver, remove the four 3.4mm screws from the right and left sides of your Panasonic Lumix Camera.

Using a small screwdriver, remove the four 3.4mm screws from the right and left sides of your Panasonic Lumix Camera.

1024

Step 2

Using a small screwdriver, remove the two 2.6mm screws located next to the battery, on the outer casing.

Using a small screwdriver, remove the two 2.6mm screws located next to the battery, on the outer casing.

Step 3

Using the plastic opening tool, open the outer cover of your device.
The easiest way to open your device is by placing the tool in the HDMI port.

Using the plastic opening tool, open the outer cover of your device.

The easiest way to open your device is by placing the tool in the HDMI port.

Step 4

Using the spudger, pull upward on the screen cable to release it.

Using the spudger, pull upward on the screen cable to release it.

Step 5

Using the plastic opening tool, lift the button board until it clicks.

Using the plastic opening tool, lift the button board until it clicks.

Step 6

Using the plastic opening tool, lift the screen until it clicks.

Using the plastic opening tool, lift the screen until it clicks.

Step 7

Using a small screwdriver, remove the two 4.2mm screws located on the corner of the inner cover, under the screen.

Using a small screwdriver, remove the two 4.2mm screws located on the corner of the inner cover, under the screen.

Step 8

Using the plastic opening tool, remove the inner cover.

Using the plastic opening tool, remove the inner cover.

Step 9

Using your hands or the opening tool, separate the device into two pieces, as shown.

Using your hands or the opening tool, separate the device into two pieces, as shown.

Step 10

Using the spudger, remove the black side cover.

Using the spudger, remove the black side cover.

Step 11

Using your hands, remove the front cover.

Using your hands, remove the front cover.

Step 12

Using the spudger, unlock the screen cables from the circuit board.
Lift up the black clip to release the cables.

Using the spudger, unlock the screen cables from the circuit board.

Lift up the black clip to release the cables.

Step 13

Using your hands, remove the lens.

Using your hands, remove the lens.

Step 14

Using the plastic opening tool, pull up on the edge of the circuit board until it clicks.
Remove the board.

Using the plastic opening tool, pull up on the edge of the circuit board until it clicks.

Remove the board.

Step 15

Using a small screwdriver, remove the 3.7 mm screw near the green chip inside the camera, as shown. This will release the top of the camera.

Using a small screwdriver, remove the 3.7 mm screw near the green chip inside the camera, as shown. This will release the top of the camera.

Step 16

Using the opening tool, pull up on the edge of the top cover to unlock it.

Using the opening tool, pull up on the edge of the top cover to unlock it.

Step 17

Using the opening tool, remove the top board.

Using the opening tool, remove the top board.

Step 18

Place the tip of the spudger at the edge of the top board, and work around three sides to loosen it.

Place the tip of the spudger at the edge of the top board, and work around three sides to loosen it.

Step 19

Using the opening tool, lift up the top board. Now you will be able to safely remove the flash.

Using the opening tool, lift up the top board. Now you will be able to safely remove the flash.

Step 20

Remove the old flash, and put in the replacement.

Remove the old flash, and put in the replacement.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors

                    Abbas Khan

Member since: 01/21/2015

482 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team 9-5, Brown Winter 2015                        

                                                  Member of USF Tampa, Team 9-5, Brown Winter 2015 



                    USFT-BROWN-W15S9G5                     


                                            3 Members                     


                                            7 Guides authored

Slice and Dice#

Introduction#

What you need#

Team#

Slice and Dice

Introduction

What you need

Team