Difficulty

Moderate

Steps

11

Time Required

                          25 - 30 minutes

Sections

1

  • Lens Assembly
  • 11 steps

Flags

2

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackPanasonic Lumix DMC-ZS6

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Make sure the device is turned off before you begin.

What you need

Step 1

              Lens Assembly
  • Remove the battery and the SD Card.

Remove the battery and the SD Card.

1024

Step 2

  • Unscrew the two bottom 1.0 mm screws with a Phillips #000 screwdriver.
  • Unscrew the two 1.0 mm screws to the left with a Phillips #000 screwdriver.
  • Unscrew the two 1.0 mm screws to the right with a Phillips #000 screwdriver.

Unscrew the two bottom 1.0 mm screws with a Phillips #000 screwdriver.

Unscrew the two 1.0 mm screws to the left with a Phillips #000 screwdriver.

Unscrew the two 1.0 mm screws to the right with a Phillips #000 screwdriver.

Step 3

  • Carefully separate the back of the camera from the main body.
  • Do not apply excessive force. The LCD is connected by ribbon cables that can be easily damaged.

Carefully separate the back of the camera from the main body.

Do not apply excessive force. The LCD is connected by ribbon cables that can be easily damaged.

Step 4

  • Use the tip of the 2.0 mm flathead screwdriver to flip up the black tabs on the ribbon cables.
  • Pull gently on the ribbon cables to unseat them.

Use the tip of the 2.0 mm flathead screwdriver to flip up the black tabs on the ribbon cables.

Pull gently on the ribbon cables to unseat them.

Step 5

  • Unscrew the two 1.0 mm screws to the left with a Phillips #000 screwdriver.
  • Unscrew the two 1.0 mm screws to the right with a Phillips #000 screwdriver.
  • Unscrew the two bottom 1.0 mm screws with a Phillips #000 screwdriver.

Step 6

  • Carefully separate the front of the camera from the main body.

Carefully separate the front of the camera from the main body.

Step 7

  • Use the tip of the 1.5 mm flathead screwdriver to disengage the plastic tab.
  • Carefully lift the selector switch away from the motherboard.

Use the tip of the 1.5 mm flathead screwdriver to disengage the plastic tab.

Carefully lift the selector switch away from the motherboard.

Step 8

  • Unscrew the three silver 1.0 mm screws with a Phillips #000 screwdriver.
  • Use the tip of the 2.0 mm flathead to disengage the metal tab, then carefully lift the shield away from the motherboard.

Unscrew the three silver 1.0 mm screws with a Phillips #000 screwdriver.

Use the tip of the 2.0 mm flathead to disengage the metal tab, then carefully lift the shield away from the motherboard.

Step 9

  • Insert the tip of the 2.0 mm flathead into the center hole of the tripod mount, and apply force in the direction facing away from the button.
  • Carefully lift the tripod mount out of the camera body.

Insert the tip of the 2.0 mm flathead into the center hole of the tripod mount, and apply force in the direction facing away from the button.

Carefully lift the tripod mount out of the camera body.

Step 10

  • Use the 2.0 mm flathead to flip up the brown tab on the motherboard and carefully unseat the ribbon cable.
  • Insert the tip of the 2.0 mm flathead screwdriver into the hole on the daughterboard, then apply upward force to remove the daughterboard from the main case.

Use the 2.0 mm flathead to flip up the brown tab on the motherboard and carefully unseat the ribbon cable.

Insert the tip of the 2.0 mm flathead screwdriver into the hole on the daughterboard, then apply upward force to remove the daughterboard from the main case.

Step 11

  • Use the 2.0 mm flathead to flip up the two tabs on the motherboard and carefully unseat the ribbon cables.
  • Unscrew the three silver 1.0 mm screws with a Phillips #000 screwdriver.
  • Carefully lift the lens assembly out of the camera.

Use the 2.0 mm flathead to flip up the two tabs on the motherboard and carefully unseat the ribbon cables.

Carefully lift the lens assembly out of the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 8 other contributors 


                    Derrick Thompson

Member since: 01/30/2018

1,035 Reputation

                                      5 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Baylor, Team S2-G5, Johnson Spring 2018                        

                                                  Member of Baylor, Team S2-G5, Johnson Spring 2018 



                    BU-JOHNSON-S18S2G5                     


                                            3 Members                     


                                            10 Guides authored