Difficulty

Easy

Steps

9

Time Required

Suggest a time??

Sections

1

  • Panasonic RF-1101 Radio Disassembly
  • 9 steps

Flags

5

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackPanasonic RF-1101 Radio

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Panasonic RF-1101 Radio Disassembly
  • Lets fix the sliders and turn knobs with Deoxit

Lets fix the sliders and turn knobs with Deoxit

1024

Step 2

  • 5 Screws Removed from the BAck

5 Screws Removed from the BAck

Step 3

              Unhook the Antenna Connector ont he right side.
  • Wire on the right is the Antenna Wire. It Attaches to the board by a connector. Unhook it so the back will lay over.

Wire on the right is the Antenna Wire. It Attaches to the board by a connector. Unhook it so the back will lay over.

Step 4

              Transformer and Battery connector
  • The transformer for AC and the Battery connector for DC

The transformer for AC and the Battery connector for DC

Step 5

              Board View
  • Board view of top and bottom of board. Remove 3 screws to take thew board out. Remember the one screw with washer in the left top. Also note the position of the screws as the screws in the back also go through the board.

Board view of top and bottom of board. Remove 3 screws to take thew board out. Remember the one screw with washer in the left top. Also note the position of the screws as the screws in the back also go through the board.

Step 6

              Battery or AC selector
  • The battery, off and AC selector runs through the front on to the back of the unit. Use Deoxit ont he slider in the front and the unit to the back of board. in 3 places. As shown

The battery, off and AC selector runs through the front on to the back of the unit. Use Deoxit ont he slider in the front and the unit to the back of board. in 3 places. As shown

Step 7

              Tunner Knob
  • Using Deoxit to clean and lubricate the tuning knob to clear up static and crackling.

Using Deoxit to clean and lubricate the tuning knob to clear up static and crackling.

Step 8

              Tunning Knob and volume
  • The Tuning knob pulls off front and the tuning mechanism unscrews with the nut. Deoxit clears up the crackling on the volume slider as well.

The Tuning knob pulls off front and the tuning mechanism unscrews with the nut. Deoxit clears up the crackling on the volume slider as well.

Step 9

              Speaker Ohms and Numbers
  • Speaker is 8 Ohm and the numbers found on the board and the back of unit.

Speaker is 8 Ohm and the numbers found on the board and the back of unit.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    T Bone

Member since: 03/11/2021

169 Reputation

                                      1 Guide authored                  



                       Badges:
                       1

Team

                       T-Bone Electronics                        

                                                  Member of T-Bone Electronics 



                    Business                     


                                            1 Member                     


                                            1 Guide authored