Difficulty

Moderate

Steps

17

Time Required

                          10 - 15 minutes

Sections

4

  • Upper Cover
  • 6 steps
  • Rear Cover
  • 3 steps
  • Zoom Lever
  • 4 steps
  • Charging Port
  • 4 steps

Flags

5

Confusing Text

Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

  • BackPanasonic SDR H-100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove Bottom Screws
  • Remove the four 4-mm screws on the bottom of the camcorder.
  • The screws are two different colors: three blacks and one silver.

Remove the four 4-mm screws on the bottom of the camcorder.

The screws are two different colors: three blacks and one silver.

1024

Step 2

              Remove Side Screws
  • Remove the three 6-mm screws on the hand-strap side of the camera.

Remove the three 6-mm screws on the hand-strap side of the camera.

Step 3

              Remove DC Input Terminal Screws
  • Pull out the charging port (DC input terminal) cover and remove the 4-mm screw located next to the input terminal.

Pull out the charging port (DC input terminal) cover and remove the 4-mm screw located next to the input terminal.

Step 4

              Remove LCD Monitor Screws
  • Flip out the LCD screen to expose the inner screws. Remove the two black 4-mm screws.
  • One screw is located by the hinge of the LCD screen. The second is close to the upper-right corner of the camcorder body.

Flip out the LCD screen to expose the inner screws. Remove the two black 4-mm screws.

One screw is located by the hinge of the LCD screen. The second is close to the upper-right corner of the camcorder body.

Step 5

              Detach Casing from Body
  • Using a firm hold on both sides of the camcorder, gently pull apart the casing under the hand strap.
  • Pressure should be evenly distributed across entire device.
  • Detach gently so the ribbon cable is not damaged!

Using a firm hold on both sides of the camcorder, gently pull apart the casing under the hand strap.

Pressure should be evenly distributed across entire device.

Detach gently so the ribbon cable is not damaged!

Step 6

              Detach Ribbon Cable from Body
  • Use tweezers to grab the ribbon cable at the connection point and slowly lift it away from the connector.
  • This linkage point connects the HDD directly to the motherboard.

Use tweezers to grab the ribbon cable at the connection point and slowly lift it away from the connector.

This linkage point connects the HDD directly to the motherboard.

Step 7

              Rear Cover
  • Unscrew the two black 4 mm screws from metal casing around the motherboard.

Unscrew the two black 4 mm screws from metal casing around the motherboard.

Step 8

  • Remove the black 4 mm screw from the back of the camcorder underneath where the battery would have been.

Remove the black 4 mm screw from the back of the camcorder underneath where the battery would have been.

Step 9

  • Pull the plastic cover on the back out and up slightly until the back feels like it’s free, then pull back on the plastic (The top cover piece and back will be detached).

Pull the plastic cover on the back out and up slightly until the back feels like it’s free, then pull back on the plastic (The top cover piece and back will be detached).

Step 10

              Zoom Lever
  • Grab the plastic piece that covers the back of the camcorder.

Grab the plastic piece that covers the back of the camcorder.

Step 11

  • Unlock the copper ribbon cable using the blue pry tool.
  • Gently detach the ribbon cable using the tweezers.

Unlock the copper ribbon cable using the blue pry tool.

Gently detach the ribbon cable using the tweezers.

Step 12

  • Unscrew the four silver 4 mm screws underneath the outer plastic cover.
  • This gives you access to the bottom of the zoom lever.

Unscrew the four silver 4 mm screws underneath the outer plastic cover.

This gives you access to the bottom of the zoom lever.

Step 13

  • Using tweezers, pull on the black piece that is connected to the underside of the zoom lever while also pushing the back piece at an angle.
  • Do not disconnect the red and black wires while you are doing this.
  • Replace with new zoom lever.

Using tweezers, pull on the black piece that is connected to the underside of the zoom lever while also pushing the back piece at an angle.

Do not disconnect the red and black wires while you are doing this.

Replace with new zoom lever.

Step 14

              Charging Port
  • Gently pull on the red and black wires directly outwards so that these wires become detached.

Gently pull on the red and black wires directly outwards so that these wires become detached.

Step 15

  • Unscrew the two silver screws on the back panel as seen in the image.

Unscrew the two silver screws on the back panel as seen in the image.

Step 16

  • Push in on the tab and lift the metal bracket. Remove the metal bracket from the back panel.

Push in on the tab and lift the metal bracket. Remove the metal bracket from the back panel.

Step 17

  • Pull up gently on the larger orange piece. Then, gently pull out the piece to release it from the plastic back panel. The charging port is now ready to be replaced.

Pull up gently on the larger orange piece. Then, gently pull out the piece to release it from the plastic back panel. The charging port is now ready to be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Caleb Osborne

Member since: 04/08/2015

801 Reputation

                                      8 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Eastern Washington University, Team 2-2, Matresse Spring 2015                        

                                                  Member of Eastern Washington University, Team 2-2, Matresse Spring 2015 



                    EWU-MATRESSE-S15S2G2                     


                                            3 Members                     


                                            16 Guides authored

tadsoloart - Aug 22, 2016

Reply

Great Info. Where I can buy this charging port?