Difficulty
Moderate
Steps
15
Time Required
40 minutes
Sections
1
- LCD
- 15 steps
Flags
Better Introduction
Improve this guide by completing or revising its introduction.
BackPanasonic VDR-D220 DVD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
LCD
- Remove all three 5mm screws from the top of the camera using a Phillips #0 screwdriver.
Remove all three 5mm screws from the top of the camera using a Phillips #0 screwdriver.
1024
Step 2
- Rotate the camera to show the bottom side of the camera.
- Remove the four 5mm screws on the bottom side of the camera with a Phillips #0 driver.
Rotate the camera to show the bottom side of the camera.
Remove the four 5mm screws on the bottom side of the camera with a Phillips #0 driver.
Step 3
- Remove one 5mm screw by using Phillips #0 screwdriver.
Remove one 5mm screw by using Phillips #0 screwdriver.
Step 4
- Pry with a spudger to disconnect the top-front part of the camera from the main body.
- Slide the top portion of the camera forward revealing more screws.
- Be careful not to remove the two sections too far as there are still cables connecting them.
Pry with a spudger to disconnect the top-front part of the camera from the main body.
Slide the top portion of the camera forward revealing more screws.
Be careful not to remove the two sections too far as there are still cables connecting them.
Step 5
- Flip the camera on the right side.
- Gently pull the front part from the main body to expose the cables connecting them.
- Do not pull too hard because of the ZIF connector cable.
- Use your plastic opening tool to disconnect the connection point safely.
- Press the tab with plastic opening tool and then pull the ZIF connector to detach.
Flip the camera on the right side.
Gently pull the front part from the main body to expose the cables connecting them.
Do not pull too hard because of the ZIF connector cable.
Use your plastic opening tool to disconnect the connection point safely.
Press the tab with plastic opening tool and then pull the ZIF connector to detach.
Step 6
- Flip the camera on the bottom side.
- Remove one more 5mm screw that had been uncovered previously with a Phillips #0 screwdriver.
Flip the camera on the bottom side.
Remove one more 5mm screw that had been uncovered previously with a Phillips #0 screwdriver.
Step 7
- Go to the battery basement’s side.
- Use your Phillips #0 screwdriver to remove the two 5mm screws on the battery base of the camera.
Go to the battery basement’s side.
Use your Phillips #0 screwdriver to remove the two 5mm screws on the battery base of the camera.
Step 8
- Rotate the camera to the left side, where the side port is located.
- Open the side port door.
Rotate the camera to the left side, where the side port is located.
Open the side port door.
Step 9
- Remove three 5mm screws inside the side ports using Phillips #0 screwdriver.
- Take off the left side of the camera.
Remove three 5mm screws inside the side ports using Phillips #0 screwdriver.
Take off the left side of the camera.
Step 10
- Rotate the camera to the battery side.
- Gently pull the side of the camera apart with only your hands.
- Do not pull too hard because of the ZIF connector cable.
- Disconnect the ribbon cable with your plastic opening tool, so that the left side of the camera can be removed.
- Press the tab with plastic opening tool and then pull the ZIF connector to detach.
Rotate the camera to the battery side.
Gently pull the side of the camera apart with only your hands.
Disconnect the ribbon cable with your plastic opening tool, so that the left side of the camera can be removed.
Step 11
- Look to the left side of the camera you have removed.
- The back side of the left side of the camera.
- Remove six 5mm screws with your Phillips #0 screwdriver.
Look to the left side of the camera you have removed.
The back side of the left side of the camera.
Remove six 5mm screws with your Phillips #0 screwdriver.
Step 12
- Take off the metal piece.
- Use your plastic opening tool to disconnect the ribbon cable. Press the tab with plastic opening tool and then pull the ZIF connector to detach.
Take off the metal piece.
Use your plastic opening tool to disconnect the ribbon cable. Press the tab with plastic opening tool and then pull the ZIF connector to detach.
Step 13
- Use a plastic spudger to apply a firm amount of pressure to pry the hinge from the rest of the camera body.
Use a plastic spudger to apply a firm amount of pressure to pry the hinge from the rest of the camera body.
Step 14
- Go back to the back side.
- Take off the small plastic piece.
- Pay attention to the ribbon cable because it goes through the plastic piece.
- Rotate the right side of the LCD counter clockwise.
- Left side of the camera after LCD is removed.
Go back to the back side.
Take off the small plastic piece.
Pay attention to the ribbon cable because it goes through the plastic piece.
Rotate the right side of the LCD counter clockwise.
Left side of the camera after LCD is removed.
Step 15
- LCD replacement part.
LCD replacement part.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Brandon Gregoire
Member since: 09/18/2019
1,313 Reputation
6 Guides authored
Badges:
4
+1 more badge
Team
Embry-Riddle Aeronautical University, Team S1-G3, Watkins Fall 2019
Member of Embry-Riddle Aeronautical University, Team S1-G3, Watkins Fall 2019
ERAU-WATKINS-F19S1G3
4 Members
14 Guides authored
