Difficulty

Moderate

Steps

13

Time Required

                          30 minutes

Sections

1

  • Mainboard and Navigation Board
  • 13 steps

Flags

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

  • BackParrot AR.Drone 2.0

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

AR.Drone 2.0 spare parts and mounting tools are available from several Parrot retailers.

What you need

Video Overview

Step 1

              Mainboard and Navigation Board
  • Remove the foam body.

Remove the foam body.

1024

Step 2

  • Disconnect the battery by pulling the two red wires apart.
  • Remove the battery by releasing the battery retaining straps.

Disconnect the battery by pulling the two red wires apart.

Remove the battery by releasing the battery retaining straps.

Step 3

  • Turn the drone upside down.
  • The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.

Turn the drone upside down.

The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.

Step 4

  • Using a spudger, separate the connector for the downward camera.
  • Remove the camera from the body by pulling it off the foam body.

Using a spudger, separate the connector for the downward camera.

Remove the camera from the body by pulling it off the foam body.

Step 5

  • Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors.
  • Use tweezers to carefully remove the ribbon from the connector.

Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors.

Use tweezers to carefully remove the ribbon from the connector.

Step 6

  • Remove the four 8mm torx screws with a T6 bit.
  • Remove the four 8mm philips head screws with a PH00 bit.

Remove the four 8mm torx screws with a T6 bit.

Remove the four 8mm philips head screws with a PH00 bit.

Step 7

  • Carefully pull the secondary board from the mainboard.

Carefully pull the secondary board from the mainboard.

Step 8

  • Turn the drone right side up
  • Remove the USB connector from the battery retaining straps.

Turn the drone right side up

Remove the USB connector from the battery retaining straps.

Step 9

  • Release the rubber clip holding the USB and battery power cable to the body.

Release the rubber clip holding the USB and battery power cable to the body.

Step 10

  • Avoid using sharp tools near the battery.
  • Push the USB and power cable through the battery panel.

Avoid using sharp tools near the battery.

Push the USB and power cable through the battery panel.

Step 11

  • Turn the drone upside down again.
  • Use a spudger to release the connector and carefully remove the ribbon.

Turn the drone upside down again.

Use a spudger to release the connector and carefully remove the ribbon.

Step 12

  • Lift the mainboard up so that you can access the back.
  • Disconnect the first connector with the white wires using a nylon spudger.
  • Disconnect the second connector with the red and black wires using a spudger.

Lift the mainboard up so that you can access the back.

Disconnect the first connector with the white wires using a nylon spudger.

Disconnect the second connector with the red and black wires using a spudger.

Step 13

  • The mainboard is now fully detached and can be removed.

The mainboard is now fully detached and can be removed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 8 other contributors 


                    David Hoyt

Member since: 04/09/2010

3,921 Reputation

                                      43 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Cal Poly, Team 25-89, Amido Spring 2010                        

                                                  Member of Cal Poly, Team 25-89, Amido Spring 2010 



                    CPSU-AMIDO-S10S25G89                     


                                            4 Members                     


                                            63 Guides authored

ydebancangancity - May 7, 2017

Reply

hey man, you make it too easy

Fugee Maoza - Jul 2, 2017

Reply

Hi i am in need of the mainboard. I dnt know where i can buy 1. Any advice

Brett Cihlar - Jul 4, 2017

Reply

I WISH I knew if this would solve my drone issues. I am a disabled teacher & biologist. I was bought the AR drone 2.0 to help keep me in good spirit as I no longer had the strength 2 hold a dslr steady. My father set everything up and he had 1 successful flight. The second flight my dad again just wanted 2 do a simple flight and it just dropped out of the air from 5 feet into grass. IT HAS NEVER WORKED SINCE :( We tried the local hobby store where

I purchased got no help only wanting 2 sell new drones. We get a message saying “UNKNOWN ERROR” since 2013 or 14 I think i have tried everything that you tube says 2 check. : No broken crossbars, blades,gears etc. Resetting will get rid of warning then will not get more that 1ft off the ground and then goes where it wants once it even held its altitude.

So any help is gr8t. Don’t have $ to waist with all medical care