Pentax Optio Wp Back Casing Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          3 minutes

Sections

Battery and SD Card
2 steps
Back Casing
4 steps

Flags

BackPentax Optio WP
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery and SD Card

The camera used to make this manual does not contain a battery or SD card
Orient the camera so you are looking at the bottom and the battery compartment is on the right hand side.

The camera used to make this manual does not contain a battery or SD card

Orient the camera so you are looking at the bottom and the battery compartment is on the right hand side.

1024

Step 2

Unlock the battery compartment by sliding the lock switch to the unlock position (away from the arrow).
Firmly push the battery cover to the right and swing open.
The battery will be located in the larger bottom slot. Slide the plastic orange tab to remove the battery.
The SD card will be located in the smaller, top slot. Push the SD card directly in to hear a small clicking sound. Then pull out the SD card.

Unlock the battery compartment by sliding the lock switch to the unlock position (away from the arrow).

Firmly push the battery cover to the right and swing open.

The battery will be located in the larger bottom slot. Slide the plastic orange tab to remove the battery.

The SD card will be located in the smaller, top slot. Push the SD card directly in to hear a small clicking sound. Then pull out the SD card.

Step 3

              Back Casing

With the battery cover swung open, use the spudger to remove the DC IN sticker.
Remove the 4.3 mm silver screw revealed.

With the battery cover swung open, use the spudger to remove the DC IN sticker.

Remove the 4.3 mm silver screw revealed.

Step 4

Reorient the camera so it is upright and you are looking at the back screen.
Remove the rubber covers in the upper and lower right side corners. Insert spudger in between the camera case and the rubber cover and push them out of their sockets. Grab the rubbers with the tweezers and set them aside. Remove both of the 4.3 mm silver screws revealed.
Remove the 4.3 mm silver screw in the lower left corner which resides under the sliding battery cover.
When removing the screw in the lower left corner, you may need to gently pry open the casing to dislodge the screw.

Reorient the camera so it is upright and you are looking at the back screen.

Remove the rubber covers in the upper and lower right side corners. Insert spudger in between the camera case and the rubber cover and push them out of their sockets. Grab the rubbers with the tweezers and set them aside. Remove both of the 4.3 mm silver screws revealed.

Remove the 4.3 mm silver screw in the lower left corner which resides under the sliding battery cover.

When removing the screw in the lower left corner, you may need to gently pry open the casing to dislodge the screw.

Step 5

Locate the 5.3mm silver screw on the edge closest to the upper left corner of the LCD screen and remove it.

Locate the 5.3mm silver screw on the edge closest to the upper left corner of the LCD screen and remove it.

Step 6

With the spudger, pry back the cover starting with the outer edge to release.
Lift the back cover off gently from left to right. Be cautious of the copper ribbon attached to the back buttons.
Detach the copper ribbon from the internals of the camera by placing a finger on top of the terminal and gently pulling on the back casing.

With the spudger, pry back the cover starting with the outer edge to release.

Lift the back cover off gently from left to right. Be cautious of the copper ribbon attached to the back buttons.

Detach the copper ribbon from the internals of the camera by placing a finger on top of the terminal and gently pulling on the back casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 8 other contributors

                    Olivia Nixon

Member since: 01/16/2011

429 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 1-13, Amido Winter 2011                        

                                                  Member of Cal Poly, Team 1-13, Amido Winter 2011 



                    CPSU-AMIDO-W11S1G13                     


                                            5 Members                     


                                            18 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team