Philips Dpm8000 Ba Slider Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Housing & Display
8 steps
Motherboard
5 steps
BA-Slider
3 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackPhilips DPM8000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

You should also have a little bowl ready to set aside screws and other small parts.

What you need

Step 1

              Anti-Static Wrist Strap

Before you start disassembling your device make sure that it is turned off.
Put on the Anti-Static Wrist Strap and clamp the end of the band to an unpaintet spot of a radiator.

Before you start disassembling your device make sure that it is turned off.

Put on the Anti-Static Wrist Strap and clamp the end of the band to an unpaintet spot of a radiator.

1024

Step 2

              Battery Lid

Remove the battery lid

Remove the battery lid

Step 3

              Battery

Remove the battery.
The battery lid is designed to function as an instrument for this task.

Remove the battery.

The battery lid is designed to function as an instrument for this task.

Step 4

              Upper Ornamental Part

Unscrew the six Torx #4 (5,3 mm) screws from both sides of the device
Collect the removed screws in a bowl or something comparable, otherwise they might get lost.

Unscrew the six Torx #4 (5,3 mm) screws from both sides of the device

Collect the removed screws in a bowl or something comparable, otherwise they might get lost.

Step 5

Remove the upper ornamental part from the housing.
If your fingernails are not long enough you can use a plastic opening tool.
When reassembling the device be aware that the six shackles on the sides of the upper ornamental part need to be placed inside the frame.

Remove the upper ornamental part from the housing.

If your fingernails are not long enough you can use a plastic opening tool.

When reassembling the device be aware that the six shackles on the sides of the upper ornamental part need to be placed inside the frame.

Step 6

              Housing/Display

Lift up the housing.
The display as well as the speaker are connected to the motherboard. Therefore you need to be careful not to harm those connections.

Lift up the housing.

The display as well as the speaker are connected to the motherboard. Therefore you need to be careful not to harm those connections.

Step 7

Unlock the connection between display and motherboard by pushing open the brown cleat.
It is recommended to use a spudger or a comparable tool for this step.
If the connection is not completely open, one of the involved components could easily be harmed.

Unlock the connection between display and motherboard by pushing open the brown cleat.

It is recommended to use a spudger or a comparable tool for this step.

If the connection is not completely open, one of the involved components could easily be harmed.

Step 8

Separate the connection by pulling out the display cable.
If the cable does not come out easily, the connection is probably still locked.
When reconnecting the display to the motherboard don’t forget to lock the connection, otherwise it will eventually come loose and you will have to redo the first eight steps of this guide.

Separate the connection by pulling out the display cable.

If the cable does not come out easily, the connection is probably still locked.

When reconnecting the display to the motherboard don’t forget to lock the connection, otherwise it will eventually come loose and you will have to redo the first eight steps of this guide.

Step 9

              Speaker

Remove the mounting spring from the speaker with a pair of tweezers.
If you just want to replace the motherboard, it is recommended to ignore the steps 9 and 10.

Remove the mounting spring from the speaker with a pair of tweezers.

If you just want to replace the motherboard, it is recommended to ignore the steps 9 and 10.

Step 10

Take off the safety mat from the speaker.
Remove the speaker from the housing.

Take off the safety mat from the speaker.

Remove the speaker from the housing.

Step 11

              Motherboard

Unscrew the eight Torx #4 (5,0 mm) screws from the motherboard.
These two screws connect the motherboard with the sliding cage. In this guide they are removed as well. Hence this is not compulsory you can decide for yourself whether you want to remove them now or later.

Unscrew the eight Torx #4 (5,0 mm) screws from the motherboard.

These two screws connect the motherboard with the sliding cage. In this guide they are removed as well. Hence this is not compulsory you can decide for yourself whether you want to remove them now or later.

Step 12

Push in the SD-Card to eject it.
If the memory card remains in its slot you will not be able to remove the motherboard.

Push in the SD-Card to eject it.

If the memory card remains in its slot you will not be able to remove the motherboard.

Step 13

Abstract the motherboard.
Lift up the motherboard as shown in the picture before completely removing it.
When inserting the motherboard first put in the side with the speaker jack on it and make sure that the microphone is placed properly under the motherboard.

Abstract the motherboard.

Lift up the motherboard as shown in the picture before completely removing it.

When inserting the motherboard first put in the side with the speaker jack on it and make sure that the microphone is placed properly under the motherboard.

Step 14

              BA-Slider

Remove the sliding cage.
When reassembling the device please make sure that the spring in the sliding cage is positioned on the bottom side of the device.

Remove the sliding cage.

When reassembling the device please make sure that the spring in the sliding cage is positioned on the bottom side of the device.

Step 15

Unscrew one crossed slot screw PH00 (4,5 mm).

Unscrew one crossed slot screw PH00 (4,5 mm).

Step 16

Remove the defective BA-Slider and replace it with the new one.

Remove the defective BA-Slider and replace it with the new one.

To reassemble your device, follow these instructions in reverse order beginning with step 15.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Andreas Holl

Member since: 11/05/2015

731 Reputation

                                      6 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Technische Universität Wien                        

                                                  Member of Technische Universität Wien 



                    Community                     


                                            2 Members                     


                                            6 Guides authored

Michael Splittgerber - Nov 28, 2022

Großes Lob. Klare Anleitung. Scharfe Fotos. Gibt von 10/ 10 Punkte.

Hab noch vergessen, was an dem Gerät war. Der Schiebeschalter ging sehr schwer. Vermutlich war irgend etwas klebriges darunter. Ich habe den Schlitten gesäubert. Er geht wieder. Vielen Dank.

Member-Contributed Guide#

Introduction#

What you need#

Team#

Member-Contributed Guide

Introduction

What you need

Team