Philips Norelco Bg2040 Bodygroom 7100 Motor Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          25 minutes            

Sections

2

• LED Board
• 7 steps
• Motor
• 3 steps

Flags

0

• BackPhilips Norelco Bodygroom 7100

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              LED Board               

• Place thumb behind trimming blade and push up to open.

Place thumb behind trimming blade and push up to open.

1024

Step 2

• Remove two screws (M2 x 9.5) on metal plate with JIS 0 screwdriver bit.
• Use spudger to pry off metal plate.
• Slide up plastic housing to remove the trimmer.

Remove two screws (M2 x 9.5) on metal plate with JIS 0 screwdriver bit.

Use spudger to pry off metal plate.

Slide up plastic housing to remove the trimmer.

Step 3

• Slide chrome outer plastic towards removed trimmer.
• Flip to the other side and repeat, sliding the chrome plastic towards removed trimmer.

Slide chrome outer plastic towards removed trimmer.

Flip to the other side and repeat, sliding the chrome plastic towards removed trimmer.

Step 4

• Remove two top screws (M2 x 6.9) with the JIS 00 screwdriver bit.
• Remove two bottom screws (M2 x 6.9) with the same bit.

Remove two top screws (M2 x 6.9) with the JIS 00 screwdriver bit.

Remove two bottom screws (M2 x 6.9) with the same bit.

Step 5

• Use spudger to pry off top of the battery cover. WARNING: fairly difficult, be aware significant amount of force required.
• Use spudger to remove bottom of the battery cover, and remove it.

Use spudger to pry off top of the battery cover. WARNING: fairly difficult, be aware significant amount of force required.

Use spudger to remove bottom of the battery cover, and remove it.

Step 6

• Use a nylon spudger to pry out battery pack and the attached LED board.

Use a nylon spudger to pry out battery pack and the attached LED board.

Step 7

• Unwrap electrical tape around the battery pack and LED board.
• Desolder the LED board from the battery pack.
• Solder the new LED board back to the connection to battery pack.

Unwrap electrical tape around the battery pack and LED board.

Desolder the LED board from the battery pack.

Solder the new LED board back to the connection to battery pack.

Step 8

              Motor               

• Please note that you do not need to remove the LED board from the battery pack for this guide. Begin the following steps after removal of the entire battery pack.
• Using the spudger, unclip the plastic housing around white casing.
• Remove one half of the black housing first, and then proceed to the next half.

Please note that you do not need to remove the LED board from the battery pack for this guide. Begin the following steps after removal of the entire battery pack.

Using the spudger, unclip the plastic housing around white casing.

Remove one half of the black housing first, and then proceed to the next half.

Step 9

• Once housing is removed, pull off shaver head. Once black housing is removed this part may fall off

Once housing is removed, pull off shaver head. Once black housing is removed this part may fall off

Step 10

• Use spudger to pry motor out of the white housing.
• Pull waterproofing case off of the motor.

Use spudger to pry motor out of the white housing.

Pull waterproofing case off of the motor.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    August Post                     

Member since: 11/07/2017

415 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       IUPUI, Team S2-G4, Harley Fall 2017                        

                                                  Member of IUPUI, Team S2-G4, Harley Fall 2017 



                    IUPUI-HARLEY-F17S2G4                     


                                            3 Members                     


                                            4 Guides authored                     

Steve Riggle - Apr 13, 2020

Reply

Great guide. Thanks