Difficulty
Moderate
Steps
8
Time Required
35 minutes - 1 hour
Sections
2
- White Outer Housing
- 4 steps
- Internal Speakers
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackPhilips PD9000 37
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
White Outer Housing
- Lay the player flat so the bottom outside is showing. Using the Phillips #0 screwdriver, unscrew all the housing screws on the bottom of the player.
- Have the player sitting upright, remove the rubber stoppers in order to get to the screw. Unscrew the inside screws by the screen using the Philips #0 screwdriver.
- Remove the rubber stoppers for the bottom two screws as well. Unscrew the middle two screws.
Lay the player flat so the bottom outside is showing. Using the Phillips #0 screwdriver, unscrew all the housing screws on the bottom of the player.
Have the player sitting upright, remove the rubber stoppers in order to get to the screw. Unscrew the inside screws by the screen using the Philips #0 screwdriver.
Remove the rubber stoppers for the bottom two screws as well. Unscrew the middle two screws.
1024
Step 2
- Open the disc flap and remove the screws inside with the Phillips #0 screwdriver. There will be three screws.
Open the disc flap and remove the screws inside with the Phillips #0 screwdriver. There will be three screws.
Step 3
- Start removing the inside black face plate of the player by using a prying method between the white outer housing and the black face plate with a metal spudger.
- Pull the black face plate off once you have pried it from the white housing. The bottom inside layer should pop off.
- Using the same prying method with the metal spudger, start prying off the screens white outer housing.
Start removing the inside black face plate of the player by using a prying method between the white outer housing and the black face plate with a metal spudger.
Pull the black face plate off once you have pried it from the white housing. The bottom inside layer should pop off.
Using the same prying method with the metal spudger, start prying off the screens white outer housing.
Step 4
- The light panel on the front can just pop right off.
- To remove the metal bar against the battery, unscrew the screws with the phillips #0 screwdriver.
- After unscrewing you can just lift the metal bar off.
The light panel on the front can just pop right off.
To remove the metal bar against the battery, unscrew the screws with the phillips #0 screwdriver.
After unscrewing you can just lift the metal bar off.
Step 5
Internal Speakers
- Desolder the wires connected to the round speakers.
Desolder the wires connected to the round speakers.
Step 6
- Place the iOpener over the entire speaker panel to warm the glue.
Place the iOpener over the entire speaker panel to warm the glue.
Step 7
- After the glue is softened, use the metal spudger to scrape the glue away.
- You may need to use the iOpener more than once per speaker, but be sure to follow the instructions for the iOpener so as not to overheat it.
After the glue is softened, use the metal spudger to scrape the glue away.
You may need to use the iOpener more than once per speaker, but be sure to follow the instructions for the iOpener so as not to overheat it.
Step 8
- Use the spudger to pry the speaker out of it’s setting.
Use the spudger to pry the speaker out of it’s setting.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Alecia Franklin
Member since: 09/28/2015
179 Reputation
1 Guide authored
Badges:
10
+7 more badges
Team
Eastern Washington University, Team 1-3, Matresse Fall 2015
Member of Eastern Washington University, Team 1-3, Matresse Fall 2015
EWU-MATRESSE-F15S1G3
3 Members
4 Guides authored
