Difficulty
Moderate
Steps
9
Time Required
10 minutes
Sections
4
- Headband
- 3 steps
- Foam Ear Pads
- 2 steps
- Drivers
- 2 steps
- Aluminum Plates
- 2 steps
Flags
0
BackPioneer Steel Wheels
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Headband
- Remove the two screws on the underside of the headband with the PH0 Phillips screw driver.
Remove the two screws on the underside of the headband with the PH0 Phillips screw driver.
1024
Step 2
- With the headband fully extended, hold the base of the headband with one hand and with your other hand, hold the top of the headband.
- With force, pull upwards.
With the headband fully extended, hold the base of the headband with one hand and with your other hand, hold the top of the headband.
With force, pull upwards.
Step 3
- Remove the rail-piece that is now sticking up by pulling it up and out of the headphone.
- Repeat on the opposite side and the headband will be released.
- During reassembly, make the sure the rail-pieces match their respective sides so the headband reinserts properly.
Remove the rail-piece that is now sticking up by pulling it up and out of the headphone.
Repeat on the opposite side and the headband will be released.
During reassembly, make the sure the rail-pieces match their respective sides so the headband reinserts properly.
Step 4
Foam Ear Pads
- While holding the base of the ear cup with one hand, insert your index finger from your other hand into the inside of the foam ear piece.
While holding the base of the ear cup with one hand, insert your index finger from your other hand into the inside of the foam ear piece.
Step 5
- With slight force, peel the foam ear pieces away from the ear cup.
- Make sure to pull out the foam ear pieces slowly. Pulling on them fast will tear the leather wrapping.
- Repeat for the opposite side if necessary.
With slight force, peel the foam ear pieces away from the ear cup.
Make sure to pull out the foam ear pieces slowly. Pulling on them fast will tear the leather wrapping.
Repeat for the opposite side if necessary.
Step 6
Drivers
- Remove the three screws located on the driver cover of the ear cup with the PH0 Phillips screw driver.
Remove the three screws located on the driver cover of the ear cup with the PH0 Phillips screw driver.
Step 7
- Pull the driver cover away from the headphone.
- Do not pull the driver cover away too fast since there are wires connecting the driver to the ear cup.
- During reassembly, make sure the two wires are pointing downward before screwing the driver back in.
Pull the driver cover away from the headphone.
Do not pull the driver cover away too fast since there are wires connecting the driver to the ear cup.
During reassembly, make sure the two wires are pointing downward before screwing the driver back in.
Step 8
Aluminum Plates
- Remove the three screws located on the driver casing.
Remove the three screws located on the driver casing.
Step 9
- With your thumb, push the middle of the aluminum piece outwards while holding the ear cup base with your other hand.
- During reassembly, make sure the aluminum plates line up with the holes for the screws.
With your thumb, push the middle of the aluminum piece outwards while holding the ear cup base with your other hand.
During reassembly, make sure the aluminum plates line up with the holes for the screws.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Garrett Leung
Member since: 04/16/2013
916 Reputation
8 Guides authored
Badges:
15
+12 more badges
Team
Cal Poly, Team 10-40, Amido Spring 2013
Member of Cal Poly, Team 10-40, Amido Spring 2013
CPSU-AMIDO-S13S10G40
4 Members
37 Guides authored
