Difficulty

Moderate

Steps

11

Time Required

                          15 - 25 minutes

Sections

4

  • Regulator
  • 2 steps
  • Battery and Grip Panels
  • 3 steps
  • Frame
  • 3 steps
  • Eyes
  • 3 steps

Flags

0

  • BackPlanet Eclipse Etha

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Regulator
  • Firmly grasp hold of the ring on the bottom of the 90 degree silver fitting on the front of the gun.
  • Pull hard, but slowly, on the macroline where it comes out of silver piece until it comes out.
  • The macroline is the black hose connecting the regulator to the tank connection.

Firmly grasp hold of the ring on the bottom of the 90 degree silver fitting on the front of the gun.

Pull hard, but slowly, on the macroline where it comes out of silver piece until it comes out.

The macroline is the black hose connecting the regulator to the tank connection.

1024

Step 2

  • Remove the regulator by unscrewing it in a clockwise direction.

Remove the regulator by unscrewing it in a clockwise direction.

Step 3

              Battery and Grip Panels
  • Use the 5/64" hex key to remove the screw shown.
  • Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.
  • If you are only replacing the battery, skip the next step.
  • The screws in this guide are interchangeable with those shown in the Eyes replacement guide.

Use the 5/64" hex key to remove the screw shown.

Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.

If you are only replacing the battery, skip the next step.

The screws in this guide are interchangeable with those shown in the Eyes replacement guide.

Step 4

  • Flip the marker over and use the 5/64" hex key to remove the screw shown.
  • Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.

Flip the marker over and use the 5/64" hex key to remove the screw shown.

Step 5

  • Carefully remove the 9V battery and connector.
  • Remove the 9V battery from the connector.

Carefully remove the 9V battery and connector.

Remove the 9V battery from the connector.

Step 6

              Frame
  • Carefully disconnect the three connectors from the circuit board.
  • Don’t worry about remembering which direction the connectors go in, they will not fit in the board in the wrong direction.

Carefully disconnect the three connectors from the circuit board.

Don’t worry about remembering which direction the connectors go in, they will not fit in the board in the wrong direction.

Step 7

  • Use the 1/8" hex key to remove the two dome-headed screws by rotating them counter-clockwise.

Use the 1/8" hex key to remove the two dome-headed screws by rotating them counter-clockwise.

Step 8

  • Be very careful during the step to avoid damage to the solenoid or wiring.
  • Gently separate the top and bottom of the marker.

Be very careful during the step to avoid damage to the solenoid or wiring.

Gently separate the top and bottom of the marker.

Step 9

              Eyes
  • Use the 5/64" hex key to turn the screw counterclockwise.
  • Carefully remove the screw and place it off to the side.
  • Remove the panel and place it off to the side.

Use the 5/64" hex key to turn the screw counterclockwise.

Carefully remove the screw and place it off to the side.

Remove the panel and place it off to the side.

Step 10

  • Carefully flip the marker over.
  • Use the 5/64" hex key to turn the screw counterclockwise.
  • Remove the screw and place it off to the side.
  • Carefully remove the panel and place it off to the side.

Carefully flip the marker over.

Remove the screw and place it off to the side.

Carefully remove the panel and place it off to the side.

Step 11

  • Grip the marker with one hand and gently pull the eyes out with your other hand.

Grip the marker with one hand and gently pull the eyes out with your other hand.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    Hannah Lancaster

Member since: 10/14/2014

132 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Cal Poly, Team 10-42, Amido Fall 2014                        

                                                  Member of Cal Poly, Team 10-42, Amido Fall 2014 



                    CPSU-AMIDO-F14S10G42                     


                                            5 Members                     


                                            7 Guides authored