Difficulty
Moderate
Steps
10
Time Required
15 minutes
Sections
4
- Grip
- 3 steps
- Macroline
- 2 steps
- Body
- 2 steps
- Eyes
- 3 steps
Flags
0
BackPlanet Eclipse Geo3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Grip
- Remove the four screws from the grip with the 5/64" allen wrench. There are two on each side.
Remove the four screws from the grip with the 5/64" allen wrench. There are two on each side.
1024
Step 2
- Pull the grip away from the frame.
Pull the grip away from the frame.
Step 3
- Pull the grip through the opening.
- The grip is connected in the middle and is one piece.
Pull the grip through the opening.
The grip is connected in the middle and is one piece.
Step 4
Macroline
- Remove the macroline from the fitting by pulling the metal ring around the end of the fitting away while pulling out the macroline.
- It helps to rotate the collar to create room to pull out macroline.
Remove the macroline from the fitting by pulling the metal ring around the end of the fitting away while pulling out the macroline.
It helps to rotate the collar to create room to pull out macroline.
Step 5
- While pulling in the metal ring on the fitting, pull the macroline out.
While pulling in the metal ring on the fitting, pull the macroline out.
Step 6
Body
- Use 1/8" allen wrench to remove screw behind regulator.
Use 1/8" allen wrench to remove screw behind regulator.
Step 7
- Use 1/8" allen wrench to loosen the screw inside the grip on the right side.
- The screw only needs to be turned a couple of times.
- Slide the upper frame forward on the rails and remove the screw from the slot to separate the two halves of the body.
- BE CAREFUL: Do not pull the two frames apart too much or too quickly. This may cause the wires to be damaged.
Use 1/8" allen wrench to loosen the screw inside the grip on the right side.
The screw only needs to be turned a couple of times.
Slide the upper frame forward on the rails and remove the screw from the slot to separate the two halves of the body.
BE CAREFUL: Do not pull the two frames apart too much or too quickly. This may cause the wires to be damaged.
Step 8
Eyes
- Use a prying tool or tweezers to gently remove the connection from the board. It is the connection with 2 black and 2 red wires.
- Pull the wire through the opening.
Use a prying tool or tweezers to gently remove the connection from the board. It is the connection with 2 black and 2 red wires.
Pull the wire through the opening.
Step 9
- Use 5/64" allen key to remove each screw from eye covers (Located on both sides of the paintball marker.)
- Pull off eye covers. (Located on both sides of the paintball marker.)
Use 5/64" allen key to remove each screw from eye covers (Located on both sides of the paintball marker.)
Pull off eye covers. (Located on both sides of the paintball marker.)
Step 10
- Gently pull out the two eyes, one on each side of the paintball marker.
- The red wire leading to the eye on the right side of the paintball marker. The black wire leads to the eye on the left side.
Gently pull out the two eyes, one on each side of the paintball marker.
The red wire leading to the eye on the right side of the paintball marker. The black wire leads to the eye on the left side.
To reassemble your device with a new eye wire, follow this guide in reverse.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Rett Triplett
Member since: 10/18/2013
801 Reputation
8 Guides authored
Badges:
6
+3 more badges
Team
Clemson, Team 13-6, Benson Fall 2013
Member of Clemson, Team 13-6, Benson Fall 2013
CLEM-BENSON-F13S13G6
3 Members
8 Guides authored
