Difficulty
Moderate
Steps
9
Time Required
20 minutes
Sections
4
- Grip
- 3 steps
- Macroline
- 2 steps
- Body
- 2 steps
- Solenoid
- 2 steps
Flags
0
BackPlanet Eclipse Geo3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Grip
- Remove the four screws from the grip with the 5/64" allen wrench. There are two on each side.
Remove the four screws from the grip with the 5/64" allen wrench. There are two on each side.
1024
Step 2
- Pull the grip away from the frame.
Pull the grip away from the frame.
Step 3
- Pull the grip through the opening.
- The grip is connected in the middle and is one piece.
Pull the grip through the opening.
The grip is connected in the middle and is one piece.
Step 4
Macroline
- Remove the macroline from the fitting by pulling the metal ring around the end of the fitting away while pulling out the macroline.
- It helps to rotate the collar to create room to pull out macroline.
Remove the macroline from the fitting by pulling the metal ring around the end of the fitting away while pulling out the macroline.
It helps to rotate the collar to create room to pull out macroline.
Step 5
- While pulling in the metal ring on the fitting, pull the macroline out.
While pulling in the metal ring on the fitting, pull the macroline out.
Step 6
Body
- Use 1/8" allen wrench to remove screw behind regulator.
Use 1/8" allen wrench to remove screw behind regulator.
Step 7
- Use 1/8" allen wrench to loosen the screw inside the grip on the right side.
- The screw only needs to be turned a couple of times.
- Slide the upper frame forward on the rails and remove the screw from the slot to separate the two halves of the body.
- BE CAREFUL: Do not pull the two frames apart too much or too quickly. This may cause the wires to be damaged.
Use 1/8" allen wrench to loosen the screw inside the grip on the right side.
The screw only needs to be turned a couple of times.
Slide the upper frame forward on the rails and remove the screw from the slot to separate the two halves of the body.
BE CAREFUL: Do not pull the two frames apart too much or too quickly. This may cause the wires to be damaged.
Step 8
Solenoid
- Using the Phillips #0 screwdriver, remove the 2 screws in the solenoid.
- Remove the solenoid.
Using the Phillips #0 screwdriver, remove the 2 screws in the solenoid.
Remove the solenoid.
Step 9
- Pry the board connection with the 2 black wires from the terminal.
- BE CAREFUL: Do not pull hard by the wires or you may dislodge them from the connection instead of removing the connection from the board.
- Pull out the wires through the opening in the top of the grip and replace the solenoid.
Pry the board connection with the 2 black wires from the terminal.
BE CAREFUL: Do not pull hard by the wires or you may dislodge them from the connection instead of removing the connection from the board.
Pull out the wires through the opening in the top of the grip and replace the solenoid.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Rett Triplett
Member since: 10/18/2013
801 Reputation
8 Guides authored
Badges:
6
+3 more badges
Team
Clemson, Team 13-6, Benson Fall 2013
Member of Clemson, Team 13-6, Benson Fall 2013
CLEM-BENSON-F13S13G6
3 Members
8 Guides authored
