Playstation 3 Super Slim Optical Drive Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 25 minutes

Sections

Power Supply Unit
9 steps
Optical Drive
2 steps

Flags

BackPlayStation 3 Super Slim
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Power Supply Unit

Remove the side HDD bay cover by sliding the panel towards the back of the device.
The bay cover is found on the right side of the device.

Remove the side HDD bay cover by sliding the panel towards the back of the device.

The bay cover is found on the right side of the device.

1024

Step 2

Remove all three black 9.8mm long screws with a T-8 security screwdriver.
Remove the blue 7.9mm long screw with a Phillips #1 screwdriver.

Remove all three black 9.8mm long screws with a T-8 security screwdriver.

Remove the blue 7.9mm long screw with a Phillips #1 screwdriver.

Step 3

Pull on the tab to remove the HDD.
The HDD should be removed and stored carefully to prevent damage to data.

Pull on the tab to remove the HDD.

The HDD should be removed and stored carefully to prevent damage to data.

Step 4

On the bottom of the device, pry out the three rubber feet covers with the metal spudger.
Remove the four black 36.3mm long screws underneath with a Phillips #1 screwdriver.
One screw is located underneath the warranty sticker. This sticker can either be peeled off or punctured through with a screwdriver.

On the bottom of the device, pry out the three rubber feet covers with the metal spudger.

Remove the four black 36.3mm long screws underneath with a Phillips #1 screwdriver.

One screw is located underneath the warranty sticker. This sticker can either be peeled off or punctured through with a screwdriver.

Step 5

On the top of the device, unlatch the hook on the furthest right beneath the front panel, lift the panel slightly and apply pressure.
Unlatch the second right-side hook by sliding a plastic opening tool in the marked area.
Slide the panel to the left to unlatch the rest of the hooks.
This is probably the most difficult part of the procedure. If you cannot unlatch the hook on the front panel, you can attempt to pry all the hooks off. However, do this at your own risk, as these hooks break easily.

On the top of the device, unlatch the hook on the furthest right beneath the front panel, lift the panel slightly and apply pressure.

Unlatch the second right-side hook by sliding a plastic opening tool in the marked area.

Slide the panel to the left to unlatch the rest of the hooks.

This is probably the most difficult part of the procedure. If you cannot unlatch the hook on the front panel, you can attempt to pry all the hooks off. However, do this at your own risk, as these hooks break easily.

Step 6

Remove the back panel by pressing down the tab on the right side of the device, and sliding the panel to the left.

Remove the back panel by pressing down the tab on the right side of the device, and sliding the panel to the left.

Step 7

Remove the five silver 20.8mm long screws with a Phillips #1 screwdriver.
Remove the two black 9.9mm long screws in the disc reader with a T-8 security screwdriver.
Remove the top black plastic shell.

Remove the five silver 20.8mm long screws with a Phillips #1 screwdriver.

Remove the two black 9.9mm long screws in the disc reader with a T-8 security screwdriver.

Remove the top black plastic shell.

Step 8

Move the optical drive to the side to reveal one of the silver 8.8mm long screws.
Remove the two silver 8.8mm long screws on either side with a Phillips #1 screwdriver.

Move the optical drive to the side to reveal one of the silver 8.8mm long screws.

Remove the two silver 8.8mm long screws on either side with a Phillips #1 screwdriver.

Step 9

Remove the cable from the plug and remove the wires from the two plastic hooks.
When removing the cable from the plug, pull on the plastic male connecter, not on the wires.
Remove the power supply unit.

Remove the cable from the plug and remove the wires from the two plastic hooks.

When removing the cable from the plug, pull on the plastic male connecter, not on the wires.

Remove the power supply unit.

Step 10

              Optical Drive

Remove the front white flex-ribbon cable by pulling upward from its base.
Remove the black and blue flex-ribbon cable behind it by pulling upward on the black tab, then pulling out the cable.

Remove the front white flex-ribbon cable by pulling upward from its base.

Remove the black and blue flex-ribbon cable behind it by pulling upward on the black tab, then pulling out the cable.

Step 11

Rotate the device 180 degrees.
Remove the back white flex-ribbon cable by pulling upward from its base.
Remove the optical drive.

Rotate the device 180 degrees.

Remove the back white flex-ribbon cable by pulling upward from its base.

Remove the optical drive.

Install the replacement optical drive. To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      11 other people completed this guide.

Author

                                      with 6 other contributors

                    Joseph O'Connor

Member since: 04/14/2016

2,122 Reputation

                                      5 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team 34-13, Maness Spring 2016                        

                                                  Member of Cal Poly, Team 34-13, Maness Spring 2016 



                    CPSU-MANESS-S16S34G13                     


                                            4 Members                     


                                            17 Guides authored

Sam Roney - Nov 22, 2019

It might be useful to have pictures of the super slim too since it’s in the title. I’m referring to CECH-3xxx / 4xxx mostly because the shell and disassembly looks a bit different. Great guide all the same. Thanks!

Karl-Heinz Schumacher - Dec 31, 2020

Hi i have a Question

I change the Optical Drive on my PS 3 Super Slim Named KEM850 PHA KES850 .But the new drive only play DVD not Blueray Game or Movie

An update was made without drive on board connected .can be this the problem. how can i fix them

Please Help

Tiago - Mar 18, 2021

How to pair a new optical drive with the old motherboard?

Joe Drew - Dec 5, 2022

PS3s and PS4s have daughterboards on their disc drives. Put the daughterboard of your old disc drive on the new one and it may work.

Robert Shelton - Sep 29, 2022

I am replacing the optical drive in my console. But didn’t note where the drive ribbon was positioned!? Every video I have found, they just pop right in…my original and replacement drives, have larger receptacles than the ribbon it self. There are at least 5 pins, that don’t have (potentially) anything connecting them, to the ribbon. I don’t want to randomly place the ribbon in one of the possible (7?) positions and fry something in the process…so where do I connect the smaller ribbon?!

Introduction#

What you need#

Team#

Introduction

What you need

Team