Playstation 4 Pro Power Supply Unit Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 15 minutes

Sections

Power Supply Unit
7 steps

Flags

BackPlayStation 4 Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Power Supply Unit

Begin by flipping the console upside down.
Use your finger to pull and snap off the plastic cover over the hard drive.

Begin by flipping the console upside down.

Use your finger to pull and snap off the plastic cover over the hard drive.

1024

Step 2

Use a screwdriver to remove the single Phillips #0 screw securing the hard drive caddy.
Pull the hard drive caddy straight out.

Use a screwdriver to remove the single Phillips #0 screw securing the hard drive caddy.

Pull the hard drive caddy straight out.

Step 3

Flip the console right side up.
Grip the two corners located at the front of the device.
Pull upwards until a loud click is heard.
This may require a lot of force, so do not be afraid to get a little rough with your console.
After both corners detach, slide the cover backwards and lift off.

Flip the console right side up.

Grip the two corners located at the front of the device.

Pull upwards until a loud click is heard.

This may require a lot of force, so do not be afraid to get a little rough with your console.

After both corners detach, slide the cover backwards and lift off.

Step 4

Use a T8 Torx Security screwdriver to remove the five screws.
Two 31mm screws.
Three 10mm screws.
Remove the metal plate.

Use a T8 Torx Security screwdriver to remove the five screws.

Two 31mm screws.

Three 10mm screws.

Remove the metal plate.

Step 5

Flip the console to its back once again.
Use a T8 Torx Security screwdriver to remove the three black 7mm screws in the back panel.
Remove the bottom cover in the same way as the top cover. Grip on both sides, pull up until a click is heard and slide off.

Flip the console to its back once again.

Use a T8 Torx Security screwdriver to remove the three black 7mm screws in the back panel.

Remove the bottom cover in the same way as the top cover. Grip on both sides, pull up until a click is heard and slide off.

Step 6

Use a T8 Torx security screwdriver to remove the two 10mm silver screws from the metal plate.

Use a T8 Torx security screwdriver to remove the two 10mm silver screws from the metal plate.

Step 7

Flip the console over to continue working on the top side.
Place fingers underneath edge of power supply unit on both sides and pull straight up.
Be careful not to pull too far, the assembly is still connected at one point.
Grip the connector behind the power supply and pull straight out.

Flip the console over to continue working on the top side.

Place fingers underneath edge of power supply unit on both sides and pull straight up.

Be careful not to pull too far, the assembly is still connected at one point.

Grip the connector behind the power supply and pull straight out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      31 other people completed this guide.

Author

                                      with 8 other contributors

                    Ashlyn Chow

Member since: 04/25/2017

2,848 Reputation

                                      1 Guide authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team S21-G5, Livingston Spring 2017                        

                                                  Member of Cal Poly, Team S21-G5, Livingston Spring 2017 



                    CPSU-LIVINGSTON-S17S21G5                     


                                            4 Members                     


                                            49 Guides authored

Fayce D D - Sep 28, 2018

Thank you soooo much for helping me save my ps4 pro guys! At the moment I love you like no one before! ;D

Matt - Jul 21, 2019

Can you go further in your tear-down and show us how to open up the power supply without breaking the PSU plastic case? Thanks. ^_^

joseph fish - Dec 8, 2019

I bought a PS4 power supply CR 300 and my PS4 has an FR 300 power supply will they interchange

My PlayStation Pro has a power supply FR 300 and the power supply I bought was a CR 300 power supply will they interchange

Tomás Javier - Jan 8, 2020

Hola como saber que tipo de fuente vida mi ps4 pro modelo 7215b

Introduction#

What you need#

Team#

Introduction

What you need

Team