Playstation Vr Microphone Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 - 35 minutes

Sections

LED Light Tracker
12 steps
Microphone
1 step

Flags

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Better Introduction

Improve this guide by completing or revising its introduction.

BackPlayStation VR
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              LED Light Tracker

Peel back the rubber covering around the lenses to remove the surrounding plastic eyepieces.

Peel back the rubber covering around the lenses to remove the surrounding plastic eyepieces.

1024

Step 2

Unscrew four 13 mm screws with a PH #000 screwdriver.

Unscrew four 13 mm screws with a PH #000 screwdriver.

Step 3

Using the plastic opening tool, carefully pry the white plastic panel free from the side of the headset. Repeat this action for the opposite side.

Using the plastic opening tool, carefully pry the white plastic panel free from the side of the headset. Repeat this action for the opposite side.

Step 4

Use the plastic opening tool to pry the top white plastic panel free from the headset.
Do not try to remove the bottom plastic panel. There is a screw attaching it that must be removed first.
There may be a small amount of adhesive attaching the top panel to the headset, in which case you may need to use a bit more force to remove the panel.

Use the plastic opening tool to pry the top white plastic panel free from the headset.

Do not try to remove the bottom plastic panel. There is a screw attaching it that must be removed first.

There may be a small amount of adhesive attaching the top panel to the headset, in which case you may need to use a bit more force to remove the panel.

Step 5

Flip the headset over.
Using a PH #000, unscrew the 7 mm screw found on the bottom of the headset.

Flip the headset over.

Using a PH #000, unscrew the 7 mm screw found on the bottom of the headset.

Step 6

Using the plastic opening tool, pry the bottom white plastic panel loose and remove it from the headset.
There is adhesive attaching the panel to the headset, in which case it will take more force to remove the panel.

Using the plastic opening tool, pry the bottom white plastic panel loose and remove it from the headset.

There is adhesive attaching the panel to the headset, in which case it will take more force to remove the panel.

Step 7

Unscrew the two 7 mm screws from the top of the headset.

Unscrew the two 7 mm screws from the top of the headset.

Step 8

Using your fingers, carefully pry the black front panel free from the headset.
We recommend that you start the removal from the sides by pulling them forward.
There is adhesive holding the front panel in place, which means you will need a bit of extra force to remove it.

Using your fingers, carefully pry the black front panel free from the headset.

We recommend that you start the removal from the sides by pulling them forward.

There is adhesive holding the front panel in place, which means you will need a bit of extra force to remove it.

Step 9

Unscrew the four silver 6 mm screws in each corner using a PH #000 screwdriver.

Unscrew the four silver 6 mm screws in each corner using a PH #000 screwdriver.

Step 10

Lift the small silver latch attaching the ZIF (zero insertion force) connector to the circuit board.
Carefully pull the end of the white ribbon connector from its slot.
Be careful not to damage or dirty the ribbon connector.

Lift the small silver latch attaching the ZIF (zero insertion force) connector to the circuit board.

Carefully pull the end of the white ribbon connector from its slot.

Be careful not to damage or dirty the ribbon connector.

Step 11

Unhitch the yellow led connector ribbon and move it aside.
Be careful not to damage or dirty the ribbon connector.

Unhitch the yellow led connector ribbon and move it aside.

Step 12

Carefully pry the black plastic piece attaching the yellow ribbon to the headset away from the green circuit board.
Remove the yellow LED ribbons and black plastic connecting piece from the headset.

Carefully pry the black plastic piece attaching the yellow ribbon to the headset away from the green circuit board.

Remove the yellow LED ribbons and black plastic connecting piece from the headset.

Step 13

              Microphone

Pinch the small white cable connector and unplug it from the motherboard.
The microphone will be attached to the white cable connector on the bottom right of the motherboard.

Pinch the small white cable connector and unplug it from the motherboard.

The microphone will be attached to the white cable connector on the bottom right of the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Elliott Ruoff

Member since: 02/15/2021

340 Reputation

                                      3 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       The Citadel Military College of South Carolina, Team S1-G10, Eggleston Spring 2021                        

                                                  Member of The Citadel Military College of South Carolina, Team S1-G10, Eggleston Spring 2021 



                    CMCSC-EGGLESTON-S21S1G10                     


                                            3 Members                     


                                            3 Guides authored

Needs More Images#

Better Introduction#

Introduction#

What you need#

Team#

Needs More Images

Better Introduction

Introduction

What you need

Team