Difficulty

Easy

Steps

8

Time Required

                          20 minutes

Sections

2

  • Battery
  • 5 steps
  • Speakers
  • 3 steps

Flags

0

  • BackPoin2 Chromebook 11

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Power down the Poin2 Chromebook 11 and disconnect the power adapter.
  • Close the Chromebook and position it with the base facing up.
  • Use a #0 Phillips screwdriver to unscrew the ten 7mm screws that hold the base to the rest of the frame
  • Poin2 Chromebook 11 does not have screws under its rubber feet at the base.

Power down the Poin2 Chromebook 11 and disconnect the power adapter.

Close the Chromebook and position it with the base facing up.

Use a #0 Phillips screwdriver to unscrew the ten 7mm screws that hold the base to the rest of the frame

Poin2 Chromebook 11 does not have screws under its rubber feet at the base.

1024

Step 2

  • Insert a 1cm-wide plastic opening tool between the base and top frame.
  • Applying pressure up and down with the tool may be necessary. When you hear a “click,” this indicates the separation of the frame.
  • Pry (up and down) around the entire border of the Chromebook to separate.
  • Use your hands to gently lift the base away from the frame.

Insert a 1cm-wide plastic opening tool between the base and top frame.

Applying pressure up and down with the tool may be necessary. When you hear a “click,” this indicates the separation of the frame.

Pry (up and down) around the entire border of the Chromebook to separate.

Use your hands to gently lift the base away from the frame.

Step 3

  • Disconnect the white 8-wire battery connector from the motherboard using a spudger to push the two L-shaped clips out of the port.
  • The connector is a tight fit and requires careful pressure for release.

Disconnect the white 8-wire battery connector from the motherboard using a spudger to push the two L-shaped clips out of the port.

The connector is a tight fit and requires careful pressure for release.

Step 4

  • Remove the six 4mm screws using a Phillips #0 screwdriver.

Remove the six 4mm screws using a Phillips #0 screwdriver.

Step 5

  • Lift the battery from the frame.

Lift the battery from the frame.

Step 6

              Speakers
  • Unplug the black speaker cable from the lower, left side of the motherboard.

Unplug the black speaker cable from the lower, left side of the motherboard.

Step 7

  • Use the opening tool to pry the two speakers away from the frame.
  • An adhesive strip attaches each speaker to the frame. The speakers should pull away with moderate force.

Use the opening tool to pry the two speakers away from the frame.

An adhesive strip attaches each speaker to the frame. The speakers should pull away with moderate force.

Step 8

  • Detach the speaker cord from the hooks holding it to the frame and lift the speakers away.

Detach the speaker cord from the hooks holding it to the frame and lift the speakers away.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Whitney Lunny

Member since: 10/05/2017

146 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Portland State University, Team S1-G3, Romaine Spring 2018                        

                                                  Member of Portland State University, Team S1-G3, Romaine Spring 2018 



                    PSUN-ROMAINE-S18S1G3                     


                                            1 Member                     


                                            2 Guides authored