Difficulty

Moderate

Steps

10

Time Required

                          15 - 35 minutes

Sections

1

  • Battery
  • 10 steps

Flags

0

  • BackPolaroid Cube

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Remove the SD card cover by twisting it using a Plastic Opening Tool

Remove the SD card cover by twisting it using a Plastic Opening Tool

1024

Step 2

  • Use the Plastic Opening tool to pry off and remove the front cover.

Use the Plastic Opening tool to pry off and remove the front cover.

Step 3

  • Using a J00 head screwdriver, remove the four 3.27mm screws from the front of the camera near the lens.

Using a J00 head screwdriver, remove the four 3.27mm screws from the front of the camera near the lens.

Step 4

  • Use the Plastic Opening Tool to pry open the shell of the camera.
  • There are four latches, one at each corner, that you will need to detach.

Use the Plastic Opening Tool to pry open the shell of the camera.

There are four latches, one at each corner, that you will need to detach.

Step 5

  • Remove shell from top and bottom of camera.

Remove shell from top and bottom of camera.

Step 6

  • Remove the rubber seal wrapped around the camera.

Remove the rubber seal wrapped around the camera.

Step 7

  • Remove the tape wrapped around the battery.

Remove the tape wrapped around the battery.

Step 8

  • Using a J00 head screwdriver, unscrew the four 3.46mm screws from the top and bottom circuit board.

Using a J00 head screwdriver, unscrew the four 3.46mm screws from the top and bottom circuit board.

Step 9

  • Use the plastic opening tool to remove the circuit board that the battery is connected to.

Use the plastic opening tool to remove the circuit board that the battery is connected to.

Step 10

  • Gently remove the battery pin connector from the circuit board.

Gently remove the battery pin connector from the circuit board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.

Author

                                      with 3 other contributors 


                    heath lamkin

Member since: 09/29/2016

372 Reputation

                                      1 Guide authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       IUPUI, Team 3-2, Harley Fall 2016                        

                                                  Member of IUPUI, Team 3-2, Harley Fall 2016 



                    IUPUI-HARLEY-F16S3G2                     


                                            4 Members                     


                                            3 Guides authored

hooverhogg - Feb 15, 2017

Reply

Any idea where to find the replacement batteries?

seyhangul - Mar 5, 2017

Reply

Well described! Need to buy a replacement battery though but I have no idea about the specs of the battery. Any information?

David F O’Connor - Jul 4, 2021

Fuji 402424 Lithium ion (Pouch)battery 240mA 4.8V Can’t find it. Can anyone help with a source?

yzorger - May 10, 2017

Reply

Was anyone able to to find the replacement batteries for the Cube?

Timothy Davenport - Jun 8, 2017

Reply

the cube requires a two-pack battery which has a single plug for both of them and so they have to be wired together in just the right way to be able to fit inside the cube. i guess it’s not possible to buy replacement batt. and paying minimum $16 for it? u could just buy a new one for too close to $16. or a used one.