Polaroid Ptab7Xc Usb Port Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

USB Port
8 steps

Flags

BackPolaroid PTAB7XC
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              USB Port

Remove the two 7 mm screws on the top of the device using a J00 Phillips screwdriver, turning the screws counterclockwise.
If the screw heads have corroded or been stripped, it may be necessary to use a larger screwdriver head, such as the J0.

Remove the two 7 mm screws on the top of the device using a J00 Phillips screwdriver, turning the screws counterclockwise.

If the screw heads have corroded or been stripped, it may be necessary to use a larger screwdriver head, such as the J0.

1024

Step 2

Pry the seam between the screen and the case on all four sides with a large plastic opening tool until the plastic case comes off.
Lift the device off of the case and flip over the device so that it sits screen side down.
The device is now free from the plastic casing.
The power and/or volume buttons may fall out at this point. There is no problem with this; however, be sure to remember to reinstall them when reassembling the device.

Pry the seam between the screen and the case on all four sides with a large plastic opening tool until the plastic case comes off.

Lift the device off of the case and flip over the device so that it sits screen side down.

The device is now free from the plastic casing.

The power and/or volume buttons may fall out at this point. There is no problem with this; however, be sure to remember to reinstall them when reassembling the device.

Step 3

Desolder the following components from the motherboard.
Desolder from the motherboard the red wire that connects to the speaker unit.
Desolder from the motherboard the black wire that connects to the speaker unit.
Desolder from the motherboard the gray wire that runs along the edge of the device.
Desolder from the motherboard the red wire that connects to the battery unit.
Desolder from the motherboard the black wire that connects to the battery unit.
The motherboard will now be detached from any wires connecting to the device.
If any of the wires do not detach completely during the desoldering process, then gently pull them off using tweezers.

Desolder the following components from the motherboard.

Desolder from the motherboard the red wire that connects to the speaker unit.

Desolder from the motherboard the black wire that connects to the speaker unit.

Desolder from the motherboard the gray wire that runs along the edge of the device.

Desolder from the motherboard the red wire that connects to the battery unit.

Desolder from the motherboard the black wire that connects to the battery unit.

The motherboard will now be detached from any wires connecting to the device.

If any of the wires do not detach completely during the desoldering process, then gently pull them off using tweezers.

Step 4

Use tweezers to unstick the medium width yellow ribbon cable from the motherboard.
Use a small plastic opening tool to slide the two small black holding clips off of the white connector to which the medium width yellow ribbon cable is attached.
Use your fingers to gently pull the medium width yellow ribbon cable out of the white connector.
Repeat the last two actions to disconnect the narrower yellow ribbon cable and the wider yellow ribbon cable from the motherboard.
The motherboard and battery will now be detached from any ribbon cables connecting to the device.

Use tweezers to unstick the medium width yellow ribbon cable from the motherboard.

Use a small plastic opening tool to slide the two small black holding clips off of the white connector to which the medium width yellow ribbon cable is attached.

Use your fingers to gently pull the medium width yellow ribbon cable out of the white connector.

Repeat the last two actions to disconnect the narrower yellow ribbon cable and the wider yellow ribbon cable from the motherboard.

The motherboard and battery will now be detached from any ribbon cables connecting to the device.

Step 5

Use the PH000 screwdriver remove the four 5 mm screws along the bottom edge of the motherboard, turning the screws counterclockwise.
The motherboard is now detached from the device.

Use the PH000 screwdriver remove the four 5 mm screws along the bottom edge of the motherboard, turning the screws counterclockwise.

The motherboard is now detached from the device.

Step 6

Lift the motherboard out of the device using your hands.
Set the motherboard down on a heat safe surface so that the gray side of the motherboard is face up.

Lift the motherboard out of the device using your hands.

Set the motherboard down on a heat safe surface so that the gray side of the motherboard is face up.

Step 7

Desolder each side of the USB port where it is attached to the motherboard.
The USB port will now be loosened from the motherboard.

Desolder each side of the USB port where it is attached to the motherboard.

The USB port will now be loosened from the motherboard.

Step 8

Using tweezers, pull the USB port straight out from the motherboard without wiggling it up, down, or side to side.
Wiggling the port may break the small connectors that remain attached to the motherboard.
The USB port is now replaceable.

Using tweezers, pull the USB port straight out from the motherboard without wiggling it up, down, or side to side.

Wiggling the port may break the small connectors that remain attached to the motherboard.

The USB port is now replaceable.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Meg Lybbert

Member since: 10/08/2015

649 Reputation

                                      5 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Eastern Washington University, Team 2-2, Plummer Fall 2015                        

                                                  Member of Eastern Washington University, Team 2-2, Plummer Fall 2015 



                    EWU-PLUMMER-F15S2G2                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team