Difficulty
Difficult
Steps
9
Time Required
1 hour
Sections
2
- Cordless Phone Base
- 3 steps
- Charger Plate
- 6 steps
Flags
0
BackPolyconcept 900-MHz Device
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Removing Power and Telephone Cords
- To disconnect the phone cord, squeeze the tab against the connector and pull the cord away from the telephone-line-in-jack.
- To disconnect the power cord, grasp the end and pull back and away until it is disconnected.
- Once disconnected remove each cord from its track.
To disconnect the phone cord, squeeze the tab against the connector and pull the cord away from the telephone-line-in-jack.
To disconnect the power cord, grasp the end and pull back and away until it is disconnected.
Once disconnected remove each cord from its track.
1024
Step 2
Removing Screws to Base Plate
- Using a Phillips #00 screwdriver, remove the six 7mm screws from the base plate.
Using a Phillips #00 screwdriver, remove the six 7mm screws from the base plate.
Step 3
Remove Bottom Plate from Base
- With the base turned upside down, grasp the edges of the base plate and gently lift from the rest of the base.
- Two wires lead from the motherboard to the charger plate, so the two parts cannot be completely separated without further steps.
With the base turned upside down, grasp the edges of the base plate and gently lift from the rest of the base.
Two wires lead from the motherboard to the charger plate, so the two parts cannot be completely separated without further steps.
Step 4
Removing the Screws from the Charger Plate
- Use a Phillips #00 screwdriver to remove the two 5mm screws from the metal plate.
Use a Phillips #00 screwdriver to remove the two 5mm screws from the metal plate.
Step 5
Removing the Plate
- Grip the metal plate and pull towards you.
- You may need to wiggle the plate back and forth gently to loosen it from its housing.
Grip the metal plate and pull towards you.
You may need to wiggle the plate back and forth gently to loosen it from its housing.
Step 6
Removing Screw from Base Cover
- Use the Philips #00 screwdriver to remove the four 6mm screws from the base cover.
Use the Philips #00 screwdriver to remove the four 6mm screws from the base cover.
Step 7
Separating Charge Plate from Base Cover
- Gently pull the charge plate away from the rest of the base and separate the two pieces of the charge plate.
Gently pull the charge plate away from the rest of the base and separate the two pieces of the charge plate.
Step 8
Removing Glue from Wires
- Use the spudger to gently scrape the glue away from the wire connections.
- If the spudger is not adequate, try using the tweezers to pull the glue away before scraping.
Use the spudger to gently scrape the glue away from the wire connections.
If the spudger is not adequate, try using the tweezers to pull the glue away before scraping.
Step 9
Desoldering the Wire Connections
- Use the soldering station to desolder the wire connections.
- For further instructions on using the soldering station click here.
Use the soldering station to desolder the wire connections.
For further instructions on using the soldering station click here.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Jay Gunter
Member since: 10/27/2014
372 Reputation
3 Guides authored
Badges:
8
+5 more badges
Team
Eastern Washington University, Team 1-1, Carnegie Fall 2014
Member of Eastern Washington University, Team 1-1, Carnegie Fall 2014
EWU-CARNEGIE-F14S1G1
6 Members
12 Guides authored
