Difficulty

Moderate

Steps

12

Time Required

Suggest a time??

Sections

1

  • Motor Assembly
  • 12 steps

Flags

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

  • BackPorter-Cable PC60TAG

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Motor Assembly
  • Using the Phillips #2 screwdriver, remove the 3/4" Phillips screw on the back cover.

Using the Phillips #2 screwdriver, remove the 3/4" Phillips screw on the back cover.

1024

Step 2

  • Holding the front of the device, carefully slide the back cover over the cord.

Holding the front of the device, carefully slide the back cover over the cord.

Step 3

  • Using the Phillips #2 screwdriver, remove the1/2" Phillips screw holding on the motor brush arm. Repeat on the other side.

Using the Phillips #2 screwdriver, remove the1/2" Phillips screw holding on the motor brush arm. Repeat on the other side.

Step 4

  • Carefully pull the motor brush arm away from the other device, you can leave the wire connected to device. Repeat on the other side.

Carefully pull the motor brush arm away from the other device, you can leave the wire connected to device. Repeat on the other side.

Step 5

  • Using the Phillips #2 screwdriver, remove the 1 inch black retainer screw.

Using the Phillips #2 screwdriver, remove the 1 inch black retainer screw.

Step 6

  • Using the Phillips #2screwdriver, remove the 4, 1/2" Phillips screws around the head gear.

Using the Phillips #2screwdriver, remove the 4, 1/2" Phillips screws around the head gear.

Step 7

  • Carefully pull the head gear away from the device, and set aside.

Carefully pull the head gear away from the device, and set aside.

Step 8

  • Using the Phillips #2 screwdriver, remove the two, 1/2" screws holding the head to the body on the bottom side of the grinder.

Using the Phillips #2 screwdriver, remove the two, 1/2" screws holding the head to the body on the bottom side of the grinder.

Step 9

  • Using the Phillips #2 screwdriver, remove the other two 1/2" screws holding the head to the body on the top side of the grinder.

Using the Phillips #2 screwdriver, remove the other two 1/2" screws holding the head to the body on the top side of the grinder.

Step 10

  • Holding the head of the device, carefully pull the motor assembly out of the body of the device.

Holding the head of the device, carefully pull the motor assembly out of the body of the device.

Step 11

  • Using a 9/16" wrench, loosen the spindle nut inside the head, from the motor assembly.

Using a 9/16" wrench, loosen the spindle nut inside the head, from the motor assembly.

Step 12

  • Pull the motor assembly away from the head.

Pull the motor assembly away from the head.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Mackenzie Fairbanks

Member since: 03/24/2016

564 Reputation

                                      5 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       UMass Dartmouth, Team 2-2, Isaacson Spring 2016                        

                                                  Member of UMass Dartmouth, Team 2-2, Isaacson Spring 2016 



                    UMASSD-ISAACSON-S16S2G2                     


                                            3 Members                     


                                            5 Guides authored