Difficulty

Moderate

Steps

9

Time Required

                          45 minutes - 1 hour

Sections

5

  • Gearcase
  • 2 steps
  • Rear Housing
  • 2 steps
  • Anvil
  • 1 step
  • Motor
  • 2 steps
  • Grip
  • 2 steps

Flags

0

  • BackPorter-Cable PCE211

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Be sure to turn off the device and unplug from the power source prior to beginning this repair.

What you need

Step 1

              Gearcase
  • Using the Hex Security SAE 7/32", remove the four 10 mm socket screws at the base of the gearcase.

Using the Hex Security SAE 7/32", remove the four 10 mm socket screws at the base of the gearcase.

1024

Step 2

  • Grip the body of the impact wrench with one hand and the gearcase in the other and firmly pull to remove it.
  • Be careful about any loose parts when removing the head.

Grip the body of the impact wrench with one hand and the gearcase in the other and firmly pull to remove it.

Be careful about any loose parts when removing the head.

Step 3

              Rear Housing
  • Remove the four 6 mm screws using a Phillips #2 screwdriver.
  • The screws are tight so you will need to use a bit of arm strength.

Remove the four 6 mm screws using a Phillips #2 screwdriver.

The screws are tight so you will need to use a bit of arm strength.

Step 4

  • Pull the rear housing off the back of the impact wrench.
  • Be careful when removing the rear case that loose parts don’t get damaged.

Pull the rear housing off the back of the impact wrench.

Be careful when removing the rear case that loose parts don’t get damaged.

Step 5

              Anvil
  • Firmly pull the to remove drill bit holder also known as the anvil.
  • Before replacing the anvil, lubricate the base for the best performance.

Firmly pull the to remove drill bit holder also known as the anvil.

Before replacing the anvil, lubricate the base for the best performance.

Step 6

              Motor
  • This section tends to get messy so it would be best to have a paper towel or microfiber towel handy.
  • Pull the motor out with your hands.

This section tends to get messy so it would be best to have a paper towel or microfiber towel handy.

Pull the motor out with your hands.

Step 7

  • Wipe out the old grease with a towel. Use the appropriate motor grease for electric tools to lubricate the top area, base of the motor, and the space the motor sits.

Wipe out the old grease with a towel. Use the appropriate motor grease for electric tools to lubricate the top area, base of the motor, and the space the motor sits.

Step 8

              Grip
  • Using the Phillips #2 screwdriver, remove the three 8 mm screws from the grip of the impact wrench.

Using the Phillips #2 screwdriver, remove the three 8 mm screws from the grip of the impact wrench.

Step 9

  • Pull the grip from the body of the impact wrench.

Pull the grip from the body of the impact wrench.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Layla Berry

Member since: 09/19/2022

657 Reputation

                                      7 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Austin Community College, Team 13-1, Watkins Fall 2022                        

                                                  Member of Austin Community College, Team 13-1, Watkins Fall 2022 



                    AUSTINCC-WATKINS-F22S13G1                     


                                            3 Members                     


                                            7 Guides authored