Difficulty

Easy

Steps

12

Time Required

Suggest a time??

Sections

4

  • Keyboard
  • 6 steps
  • Heat Shield
  • 2 steps
  • Hard Drive
  • 3 steps
  • Processor
  • 1 step

Flags

0

  • BackPowerBook G3 Wallstreet

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Keyboard
  • Remove both expansion bay modules using the levers on the front of the computer.
  • Insert your index fingers inside the expansion bays and search for the two ribbed tabs on the underside of the upper case. The tabs are located near the bottom corners of the keyboard.
  • Pull the tabs toward yourself and the keyboard will pop up.

Remove both expansion bay modules using the levers on the front of the computer.

Insert your index fingers inside the expansion bays and search for the two ribbed tabs on the underside of the upper case. The tabs are located near the bottom corners of the keyboard.

Pull the tabs toward yourself and the keyboard will pop up.

1024

Step 2

  • Pull the keyboard forward to disengage the tabs holding it in back and rotate it toward you.
  • Rest the keyboard on the trackpad.

Pull the keyboard forward to disengage the tabs holding it in back and rotate it toward you.

Rest the keyboard on the trackpad.

Step 3

  • This is a diagram of the ribbon clamp connectors you will disconnect in the next step.
    1. With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
    1. After disengaging the locking bar, slide the cable out of the connector.

This is a diagram of the ribbon clamp connectors you will disconnect in the next step.

  1. With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).

  2. After disengaging the locking bar, slide the cable out of the connector.

Step 4

  • Disconnect the two keyboard connectors by disengaging the clamps and pulling the ribbons directly upward.

Disconnect the two keyboard connectors by disengaging the clamps and pulling the ribbons directly upward.

Step 5

  • Slide a spudger downward between each plastic strain relief cable and the wall of the case in order to bow out the cable beyond the small tab holding it in place.
  • Once the strain relief cables are free, lift the keyboard off.

Slide a spudger downward between each plastic strain relief cable and the wall of the case in order to bow out the cable beyond the small tab holding it in place.

Once the strain relief cables are free, lift the keyboard off.

Step 6

  • Your laptop should look approximately like this.

Your laptop should look approximately like this.

Step 7

              Heat Shield
  • Remove the two Phillips screws from the heat shield.
  • One screw is shorter than the other. When putting the Wallstreet back together, this screw goes in the middle of the heat shield.

Remove the two Phillips screws from the heat shield.

One screw is shorter than the other. When putting the Wallstreet back together, this screw goes in the middle of the heat shield.

Step 8

  • Grasp the metal handle on the heat shield and pull up and toward yourself.

Grasp the metal handle on the heat shield and pull up and toward yourself.

Step 9

              Hard Drive
  • Unscrew, but do not remove, the single Phillips screw from the hard drive bracket.

Unscrew, but do not remove, the single Phillips screw from the hard drive bracket.

Step 10

  • Grasp the hard drive bracket on the left side and pull up and to the left.

Grasp the hard drive bracket on the left side and pull up and to the left.

Step 11

Step 12

              Processor
  • Use a spudger, the tips of your fingers, or a flat non-metal tool to pry up the processor’s right side.
  • Remove the processor by sliding it up and to the right.
  • The processor and RAM can be removed as a unit. It is not necessary to remove the RAM from the processor.
  • There are two tabs on the left side of the processor that fit into slots on the metal framework. Make sure these tabs are in the slots.

Use a spudger, the tips of your fingers, or a flat non-metal tool to pry up the processor’s right side.

Remove the processor by sliding it up and to the right.

The processor and RAM can be removed as a unit. It is not necessary to remove the RAM from the processor.

There are two tabs on the left side of the processor that fit into slots on the metal framework. Make sure these tabs are in the slots.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Attached Documents

  • G3-Wallstreet-Screw-Guide.pdf
  • PDF - 282.41 kb
  • View

G3-Wallstreet-Screw-Guide.pdf

PDF - 282.41 kb

Author

                                      with 4 other contributors 


                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36





                                                        +33 more badges