Powerbook G4 Aluminum 15 1 67 Ghz Left Fan Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

Suggest a time??

Sections

Battery
1 step
Upper Case
9 steps
Left Fan
1 step

Flags

BackPowerBook G4 Aluminum 15" 1.67 GHz
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use a coin to turn the battery locking screw 90 degrees clockwise.
Lift the battery out of the computer.

Use a coin to turn the battery locking screw 90 degrees clockwise.

Lift the battery out of the computer.

1024

Step 2

              Upper Case

Remove the following 10 screws:
Two 3 mm Phillips in the battery compartment, on either side of the battery contacts.
Four 3 mm Phillips around the memory compartment.
Four 16 mm Phillips along the hinge.

Remove the following 10 screws:

Two 3 mm Phillips in the battery compartment, on either side of the battery contacts.

Four 3 mm Phillips around the memory compartment.

Four 16 mm Phillips along the hinge.

Step 3

Remove the memory compartment cover.
Remove the two 12 mm Phillips screws on the Aluminum bracket at the top of the memory compartment.

Remove the memory compartment cover.

Remove the two 12 mm Phillips screws on the Aluminum bracket at the top of the memory compartment.

Step 4

Rotate the computer 90 degrees clockwise so the power receptacle faces you.
Remove the three 3 mm Phillips screws along the edge of the lower case.
When replacing these screws, you must install them in the correct order. Begin by installing the screw closest to the display hinge, then work your way toward the front of the computer.

Rotate the computer 90 degrees clockwise so the power receptacle faces you.

Remove the three 3 mm Phillips screws along the edge of the lower case.

When replacing these screws, you must install them in the correct order. Begin by installing the screw closest to the display hinge, then work your way toward the front of the computer.

Step 5

Turn the computer 90 degrees clockwise so the hinge faces you.
Remove the lower 5 mm Phillips screw on each side of the hinge (two total).

Turn the computer 90 degrees clockwise so the hinge faces you.

Remove the lower 5 mm Phillips screw on each side of the hinge (two total).

Step 6

Rotate the computer 90 degrees clockwise so the ports face you.
Remove the three 3 mm Phillips screws along the edge of the lower case.
When replacing these screws, you must install them in the correct order. Begin by installing the screw closest to the display hinge, then work your way toward the front of the computer. Also, be careful not to put the screws in the two holes on either side of the video out port.

Rotate the computer 90 degrees clockwise so the ports face you.

When replacing these screws, you must install them in the correct order. Begin by installing the screw closest to the display hinge, then work your way toward the front of the computer. Also, be careful not to put the screws in the two holes on either side of the video out port.

Step 7

Turn the computer over and open the display.
Remove the two 4.2 mm long, 1.5 mm hex screws at the top corners of the upper case (two total).
A T6 Torx driver will work, but repeated use will strip the screws.

Turn the computer over and open the display.

Remove the two 4.2 mm long, 1.5 mm hex screws at the top corners of the upper case (two total).

A T6 Torx driver will work, but repeated use will strip the screws.

Step 8

Grasp the back corners of the upper case and pull up.
Do not pull the upper case off yet; you still need to disconnect the keyboard and trackpad cable.
Lift the back of the case up and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.

Grasp the back corners of the upper case and pull up.

Do not pull the upper case off yet; you still need to disconnect the keyboard and trackpad cable.

Lift the back of the case up and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.

Step 9

Rotate the upper case up and toward the screen, so that the upper case rests against it.

Rotate the upper case up and toward the screen, so that the upper case rests against it.

Step 10

Remove the amber tape securing the trackpad ribbon to the logic board.
Disconnect the trackpad ribbon from the logic board by pulling up on the connector.
Remove the upper case from the computer.

Remove the amber tape securing the trackpad ribbon to the logic board.

Disconnect the trackpad ribbon from the logic board by pulling up on the connector.

Remove the upper case from the computer.

Step 11

              Left Fan

Disconnect the four cables resting on the fan (shown in yellow boxes).
Remove the Phillips screws from each corner of the fan (four total).
Lift the fan out of its housing, peeling off tape as necessary.

Disconnect the four cables resting on the fan (shown in yellow boxes).

Remove the Phillips screws from each corner of the fan (four total).

Lift the fan out of its housing, peeling off tape as necessary.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Attached Documents

Aluminum-15"-Screw-Guide.pdf
PDF - 647.44 kb
View

Aluminum-15"-Screw-Guide.pdf

PDF - 647.44 kb

Author

                                      with 3 other contributors

                    Andrew Bookholt

575,478 Reputation

                                      618 Guides authored                  



                       Badges:
                       47





                                                        +44 more badges

Introduction#

What you need#

Attached Documents#

Introduction

What you need

Attached Documents