Difficulty
Moderate
Steps
14
Time Required
40 minutes
Sections
2
- Side Panel
- 4 steps
- Lens
- 10 steps
Flags
1
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
BackPowerLead Puto PLD003
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Side Panel
- Slide the battery eject button open to release the battery door.
Slide the battery eject button open to release the battery door.
1024
Step 2
- With the battery door open, carefully remove all four 5 mm Phillips #1 screws.
With the battery door open, carefully remove all four 5 mm Phillips #1 screws.
Step 3
- Rotate the camera so that the underside is facing up.
- Remove the four 5 mm Phillips #1 screws.
Rotate the camera so that the underside is facing up.
Remove the four 5 mm Phillips #1 screws.
Step 4
- Place the camera on a flat surface, with its underside facing you.
- Gently pull up on the side panel to remove it from the camera.
Place the camera on a flat surface, with its underside facing you.
Gently pull up on the side panel to remove it from the camera.
Step 5
Lens
- Remove the three 4 mm Phillips #1 screws holding the weight.
- Remove the weight.
Remove the three 4 mm Phillips #1 screws holding the weight.
Remove the weight.
Step 6
- Remove the two 4 mm Phillips #1 screws holding the back panel in place.
Remove the two 4 mm Phillips #1 screws holding the back panel in place.
Step 7
- Apply pressure to the back panel (away from the camera) to remove.
Apply pressure to the back panel (away from the camera) to remove.
Step 8
- Set aside back panel for now.
- Remove the final 4 mm Phillips #1 screw holding the screen in place. It is very small and hard to see.
Set aside back panel for now.
Remove the final 4 mm Phillips #1 screw holding the screen in place. It is very small and hard to see.
Step 9
- Carefully apply pressure, away from the camera, to the screen to detach it from the body.
- The white cord should still be connected to the body.
- OPTIONAL: Remove the screen to make accessing the lens easier
Carefully apply pressure, away from the camera, to the screen to detach it from the body.
The white cord should still be connected to the body.
OPTIONAL: Remove the screen to make accessing the lens easier
Step 10
- Unscrew the two 4 mm Phillips #1 screws holding onto the lens casing
- There are also two 4 mm Phillips #1 screws on the other side holding onto the lens casing, remove them as well.
Unscrew the two 4 mm Phillips #1 screws holding onto the lens casing
There are also two 4 mm Phillips #1 screws on the other side holding onto the lens casing, remove them as well.
Step 11
- Pull forward on the lens casing to remove it. The cord connecting the light to the motherboard should still be attached.
Pull forward on the lens casing to remove it. The cord connecting the light to the motherboard should still be attached.
Step 12
- Unscrew the three 4 mm Phillips #1 screws holding the plastic lens holder.
Unscrew the three 4 mm Phillips #1 screws holding the plastic lens holder.
Step 13
- Remove the plastic lens holder.
Remove the plastic lens holder.
Step 14
- Push the lens out of the plastic casing from the back.
- Insert new lens into the plastic casing.
Push the lens out of the plastic casing from the back.
Insert new lens into the plastic casing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Justin Tew
Member since: 03/31/2016
767 Reputation
7 Guides authored
Badges:
13
+10 more badges
Team
Eastern Washington University, Team 1-2, Giguere Spring 2016
Member of Eastern Washington University, Team 1-2, Giguere Spring 2016
EWU-GIGUERE-S16S1G2
4 Members
7 Guides authored
