Difficulty
Moderate
Steps
13
Time Required
30 minutes
Sections
2
- Side Panel
- 4 steps
- Zoom Button
- 9 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackPowerLead Puto PLD003
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Side Panel
- Slide the battery eject button open to release the battery door.
Slide the battery eject button open to release the battery door.
1024
Step 2
- With the battery door open, carefully remove all four 5 mm Phillips #1 screws.
With the battery door open, carefully remove all four 5 mm Phillips #1 screws.
Step 3
- Rotate the camera so that the underside is facing up.
- Remove the four 5 mm Phillips #1 screws.
Rotate the camera so that the underside is facing up.
Remove the four 5 mm Phillips #1 screws.
Step 4
- Place the camera on a flat surface, with its underside facing you.
- Gently pull up on the side panel to remove it from the camera.
Place the camera on a flat surface, with its underside facing you.
Gently pull up on the side panel to remove it from the camera.
Step 5
Zoom Button
- Remove the 4 mm Phillips #1 screws holding the weight.
- Remove the weight.
Remove the 4 mm Phillips #1 screws holding the weight.
Remove the weight.
Step 6
- Remove the two 4 mm Phillips #1 screws holding the back panel in place.
Remove the two 4 mm Phillips #1 screws holding the back panel in place.
Step 7
- Apply pressure to the back panel, pulling away from the camera to remove it.
Apply pressure to the back panel, pulling away from the camera to remove it.
Step 8
- Remove the final 4 mm Phillips #1 screw holding the screen in place.
- This screw is very small and hard to see.
Remove the final 4 mm Phillips #1 screw holding the screen in place.
This screw is very small and hard to see.
Step 9
- Carefully apply pressure away from the camera to the screen to detach it from the body.
- The white cord should still be connected to the body.
- OPTIONAL: Remove the screen to make accessing the zoom button easier.
Carefully apply pressure away from the camera to the screen to detach it from the body.
The white cord should still be connected to the body.
OPTIONAL: Remove the screen to make accessing the zoom button easier.
Step 10
- Remove the three 4 mm Phillips #1 screws holding the top panel in place.
Remove the three 4 mm Phillips #1 screws holding the top panel in place.
Step 11
- Push upward on the top panel to remove it from the body of the camera.
Push upward on the top panel to remove it from the body of the camera.
Step 12
- Remove the two 4 mm Phillips #1 screws holding the circuit board in place.
- Do not remove the silver screws.
Remove the two 4 mm Phillips #1 screws holding the circuit board in place.
Do not remove the silver screws.
Step 13
- Lift the circuit board out of the plastic casing.
- Gently pull on the zoom button to remove it from the circuit board.
Lift the circuit board out of the plastic casing.
Gently pull on the zoom button to remove it from the circuit board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Justin Tew
Member since: 03/31/2016
767 Reputation
7 Guides authored
Badges:
13
+10 more badges
Team
Eastern Washington University, Team 1-2, Giguere Spring 2016
Member of Eastern Washington University, Team 1-2, Giguere Spring 2016
EWU-GIGUERE-S16S1G2
4 Members
7 Guides authored
