Powerray Vertical Propeller Module Replacement Procedure Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Vertical Propeller Module
14 steps

Flags

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackPowerRay
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Step 1

              Removing the CD case assembly

Remove the four protective parts on the back of the main unit
Check the position of the claws and be careful not to break the parts.

Remove the four protective parts on the back of the main unit

Check the position of the claws and be careful not to break the parts.

1024

Step 2

              Removing the CD case assembly

Remove all screws shown in the picture
M2.5×6 (16 pieces)
M2×5 (2 pieces)
Remove CD case assembly after removing all screws

Remove all screws shown in the picture

M2.5×6 (16 pieces)

M2×5 (2 pieces)

Remove CD case assembly after removing all screws

Step 3

              Removing the AB case assembly

Remove all the following screws
M2.5×12 (8 pieces)
M2×5 (4 pieces)
After removing the screws, take care not to cut the LED wiring connected to the AB case assembly and remove the main unit.

Remove all the following screws

M2.5×12 (8 pieces)

M2×5 (4 pieces)

After removing the screws, take care not to cut the LED wiring connected to the AB case assembly and remove the main unit.

Step 4

              Removing Cabin Upper Cover Assembly

Remove all the following screws
M2.5×8 (48 pieces)

M2.5×8 (48 pieces)

Step 5

              Removing the Vertical Propeller Module

Remove all the following screws on the back of the Cabin
M2.5×8 (8 pieces)

Remove all the following screws on the back of the Cabin

M2.5×8 (8 pieces)

Step 6

              Installing the Vetical Propeller Module

Remove the three wires connected to the Vertical Propeller Module
After disconnecting the wiring, remove the faulty Vertical Propeller Module

Remove the three wires connected to the Vertical Propeller Module

After disconnecting the wiring, remove the faulty Vertical Propeller Module

Step 7

              Removing the Vertical Propeller Module

Install the Vertical Propeller Module so that it fits in the groove of the main unit.
Turn over the main unit and attach the following screws from the back side.
M2.5×8 (8 pieces) [39.2N・m]

Install the Vertical Propeller Module so that it fits in the groove of the main unit.

Turn over the main unit and attach the following screws from the back side.

M2.5×8 (8 pieces) [39.2N・m]

Step 8

              Installing the Vertical Propeller Module

There are three cables for the motor, and connect the cables of the same color to each
Make sure that it rotates in the same direction as the photo when you operate the controller to descend or ascend.
Reverse the connections of the red and blue cables if they are rotating in the opposite direction of operation

There are three cables for the motor, and connect the cables of the same color to each

Make sure that it rotates in the same direction as the photo when you operate the controller to descend or ascend.

Reverse the connections of the red and blue cables if they are rotating in the opposite direction of operation

Step 9

              Installing the Vertical Propeller Module

After confirming the direction of rotation of the motor, attach shrinkable tubes to the three motor cables for insulation.

After confirming the direction of rotation of the motor, attach shrinkable tubes to the three motor cables for insulation.

Step 10

              Installing Cabin Upper Cover Assembly

Install the bottom screws at the positions shown in the photo
M2.5 × 8 (48 Pieces) [39.2cN・m]

Install the bottom screws at the positions shown in the photo

M2.5 × 8 (48 Pieces) [39.2cN・m]

Step 11

              Installing the AB case assembly

Install the following screws at the positions shown in the photo.
Red M2.5 × 12 (6 pieces)
Blue M2 × 5 (4 pieces)

Install the following screws at the positions shown in the photo.

Red M2.5 × 12 (6 pieces)

Blue M2 × 5 (4 pieces)

Step 12

              Tightness test

Remove the airtight bolt at the rear of the main unit and attach the airtightness test valve
Pressurize up to 100kPa with a pump
Under pressure, put the main unit in water and check for 3 minutes without air leakage.

Remove the airtight bolt at the rear of the main unit and attach the airtightness test valve

Pressurize up to 100kPa with a pump

Under pressure, put the main unit in water and check for 3 minutes without air leakage.

Step 13

              Installing the CD case assembly

Install the following screws at the positions shown in the photo.
M2.5 × 6 (14 Total)
M2 × 5 (2 Total)

M2.5 × 6 (14 Total)

M2 × 5 (2 Total)

Step 14

              Installing the CD case assembly

Attach the protective parts to the position shown in the photo
Affix the propeller warning sticker and serial number display sticker

Attach the protective parts to the position shown in the photo

Affix the propeller warning sticker and serial number display sticker

To reassemble your device, follow these steps in reverse order.

Cancel: I did not complete this guide.

        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

Tech Guy

Midori Doi

Author

                                      with 1 other contributor

                    hornet

Member since: 04/04/2018

667 Reputation

                                      5 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

In Progress#

Member-Contributed Guide#

In Progress

Member-Contributed Guide